ST7FLITE35F2M6 STMicroelectronics, ST7FLITE35F2M6 Datasheet - Page 135

• Manufacturer Part Number: ST7FLITE35F2M6
• Description: IC MCU 8BIT 8K FLASH 20SOIC
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST7FLITE35F2M6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: LINSCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 15
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 7x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SOIC (7.5mm Width)
• Processor Series: ST7FLITE3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: LINSCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7FLITE-SK/RAIS, ST7MDT10-DVP3, ST7MDT10-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 7 Channel
• For Use With: 497-5858 - EVAL BOARD PLAYBACK ST7FLITE497-5085 - EVAL BOARD UNIV MOTOR CONTROL497-5049 - KIT STARTER RAISONANCE ST7FLITE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

EXAMPLE:
The following C program shows the use of the TIMERx functions. Here, x=A as TIMERA is
used. You must define TIMERA in ST7lib_config.h.
Program description:
It compares the output compare2 register value with the free running counter, checks the oc-
currence of (event) leading edge at ICAP2 pin. It generates PWM signal with a frequency of
10KHz and a Duty cycle of 33% on the OCMP1 pin, if _Enable_PWM_ is defined in
ST7lib_confi.h or it generates a 5ms pulse at OCMP1 pin, if _Enable_OPM_ is defined in
ST7lib_config.h (Fcpu = 8 MHz).
/* Program start */
#include "st7lib_config.h"
//prototype declaration
void main(void);
void TIMERA_IT_Routine(void);
void main(void)
{
}
/* Program end */
/* ----------------------------------------------------------------------------
ROUTINE NAME : TIMERA_IT_Routine
INPUT
OUTPUT
unsigned int OCR_VALUE = 0x2050;
IO_Input (IO_FLOATING,IO_PORT_F,((unsigned char)IO_PIN_5 | (unsigned char)
TIMERA_Init (TIMER_FCPU_8);
EnableInterrupts
/* Timer compares 0x2050 with free running counter
TIMERA_OCMP_Mode(TIMER_OCMP_2,OCR_VALUE,TIMER_OUTPUT_R );
while(!(TIMERA_Status_Flag(TIMER_FLAG_OCF2)== TRUE));
TIMERA_Clear_Flag(TIMER_FLAG_OCF2);
TIMERA_IT_Enable(TIMER_ICAP_IT_ENABLE);
TIMERA_ICAP_Mode(TIMER_ICAP_2,TIMER_EDGE_1);
/* Run TIMERA in PWM mode if _Enable_PWM_ is defined
#ifdef _Enable_PWM_
TIMERA_PWM_Mode(TIMER_OUTPUT1_F,TIMER_OUTPUT2_R,(unsigned int)0x001C,
#endif
/* Run TIMERA in OPM mode if _Enable_OPM_ is defined
#ifdef _Enable_OPM_
TIMERA_Clear_Flag(TIMER_FLAG_ICF1);
TIMERA_Mode_Disable(TIMER_MODE_5);
TIMERA_OPM_Mode(TIMER_EDGE_1,TIMER_OUTPUT1_F,TIMER_OUTPUT2_R,
#endif
while(1);
: None
: None
/* Timer Clock to Fcpu/8 and reset counter */
/* ICAP1,ICAP2 pins asloating input */
(unsigned int)0x1383);
/*Detect rising edge at ICAP2 pin*/
/* Clear output compare2 flag */
/* Clear Input capture1 Flag */
/* Enable capture interrupt */
(unsigned int)0x005F);
/* Clear I bit in CC reg */
Function Descriptions
/* For testing only */
*/
*/
*/
IO_PIN_6));
/* Generate PWM */
/* Disable PWM */
/* 5ms pulse */
135/235