R5F21257SNFP#U0 Renesas Electronics America, R5F21257SNFP#U0 Datasheet - Page 340

• Manufacturer Part Number: R5F21257SNFP#U0
• Description: IC R8C/25 MCU FLASH 52LQFP
• Manufacturer: Renesas Electronics America
• Series: R8C/2x/25r

Specifications of R5F21257SNFP#U0

• Core Processor: R8C
• Core Size: 16/32-Bit
• Speed: 20MHz
• Connectivity: I²C, LIN, SIO, SSU, UART/USART
• Peripherals: POR, Voltage Detect, WDT
• Number Of I /o: 41
• Program Memory Size: 48KB (48K x 8)
• Program Memory Type: FLASH
• Ram Size: 2.5K x 8
• Voltage - Supply (vcc/vdd): 2.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 52-LQFP
• For Use With: R0K521256S000BE - KIT EVAL STARTER FOR R8C/25
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R8C/24 Group, R8C/25 Group
Rev.3.00
REJ09B0244-0300
Figure 16.13
16.2.5.2
Figure 16.13 shows an Example of Clock Synchronous Serial I/O with Chip Select Operation for Data
Transmission (Clock Synchronous Communication Mode). During data transmission, the clock synchronous
serial I/O with chip select operates as described below.
When clock synchronous serial I/O with chip select is set as a master device, it outputs a synchronous clock and
data. When clock synchronous serial I/O with chip select is set as a slave device, it outputs data synchronized
with the input clock.
When the TE bit is set to 1 (transmit enabled) before writing the transmit data to the SSTDR register, the TDRE
bit is automatically set to 0 (data not transferred from registers SSTDR to SSTRSR) and the data is transferred
from registers SSTDR to SSTRSR.
After the TDRE bit is set to 1 (data transferred from registers SSTDR to SSTRSR), transmission starts. When
the TIE bit in the SSER register is set to 1, the TXI interrupt request is generated. When one frame of data is
transferred while the TDRE bit is set to 0, data is transferred from registers SSTDR to SSTRSR and
transmission of the next frame is started. If the 8th bit is transmitted while the TDRE bit is set to 1, the TEND
bit in the SSSR register is set to 1 (the TDRE bit is set to 1 when the last bit of the transmit data is transmitted)
and the state is retained. The TEI interrupt request is generated when the TEIE bit in the SSER register is set to
1 (transmit-end interrupt request enabled). The SSCK pin is fixed “H” after transmit-end.
Transmission cannot be performed while the ORER bit in the SSSR register is set to 1 (overrun error). Confirm
that the ORER bit is set to 0 before transmission.
Figure 16.14 shows a Sample Flowchart of Data Transmission (Clock Synchronous Communication Mode).
TDRE bit in
SSSR register
TEND bit in
SSSR register
Feb 29, 2008
Processing
by program
• SSUMS = 0 (clock synchronous communication mode), CPHS = 0 (data change at
Data Transmission
Example of Clock Synchronous Serial I/O with Chip Select Operation for Data
Transmission (Clock Synchronous Communication Mode)
odd numbers), and CPOS = 0 (“H” when clock stops)
SSCK
SSO
1
0
1
0
Page 321 of 485
Write data to SSTDR register
TXI interrupt request generation
b0
b1
1 frame
b7
b0
TEI interrupt request
generation
16. Clock Synchronous Serial Interface
b1
1 frame
b7