UPD78F9212CS-CAB-A Renesas Electronics America, UPD78F9212CS-CAB-A Datasheet - Page 360

• Manufacturer Part Number: UPD78F9212CS-CAB-A
• Description: MCU 8BIT 4KB FLASH 16PIN
• Manufacturer: Renesas Electronics America
• Series: 78K0S/Kx1+r

Specifications of UPD78F9212CS-CAB-A

• Core Processor: 78K0S
• Core Size: 8-Bit
• Speed: 10MHz
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 13
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Connectivity: -

358
3rd edition
Edition
Modification of Figure 12-1 Block Diagram of Reset Function
Addition of delay time of internal reset signal generation to Figure 12-2 Timing of Reset
by RESET Input and Figure 12-4 Reset Timing by RESET Input in STOP Mode
Modification of Figure 13-3 Example of Software Processing After Release of Reset
Modification of Figure 14-1 Block Diagram of Low-Voltage Detector
Modification of Note 1 in Figure 14-2 Format of Low-Voltage Detect Register (LVIM)
Modification of Note in Figure 14-3 Format of Low-Voltage Detection Level Select
Register (LVIS)
Modification of INTLVI and Note 2 in Figure 14-5 Timing of Low-Voltage Detector
Interrupt Signal Generation
Modification of (2) in <Action> of 14.5 Cautions for Low-Voltage Detector
Modification of Figure 14-6 Example of Software Processing After Release of Reset
(1/2)
Modification of description and configuration in CHAPTER 15 OPTION BYTE
Modification of Caution in Figure 15-2 Format of Option Byte (1/2)
Addition of Remarks 3, 4 to Figure 15-2 Format of Option Byte (2/2)
Modification of and addition to 16.1 Features
Figure 16-2 Environment for Writing Program to Flash Memory is divided into two
figures, in the case of FlashPro4 and in the case of PG-FPL2
Modification of Caution in Table 16-5 Oscillation Frequency and PG-FP4 GUI
Software Setting Value Example
Deletion of 16.7.1 Flash memory programming mode
Modification of 16.7.2 Communication commands
Modification of and Addition to 16.8.2 Cautions on self programming function
Addition of <Setting conditions> in 3. Operating conditions of WEPRERR flag of
16.8.3 Registers used for self programming function (3)
Addition of description to Figure 16-15 Format of Flash Programming Command
Register (FLCMD)
Modification of Caution in Figure 16-16 Format of Flash Address Pointer H/L
(FLAPH/FLAPL)
Modification of Caution 2 in Figure 16-17 Format of Flash Address Pointer H/L
Compare Registers (FLAPHC/FLAPLC)
Complete revision of CHAPTER 18 ELECTRICAL SPECIFICATIONS (TARGET
VALUES), and addition of chapters
APPENDIX E REVISION HISTORY
User’s Manual U16994EJ6V0UD
Description
CHAPTER 12 RESET
FUNCTION
CHAPTER 13 POWER-
ON-CLEAR CIRCUIT
CHAPTER 14 LOW-
VOLTAGE DETECTOR
CHAPTER 15 OPTION
BYTE
CHAPTER 16 FLASH
MEMORY
CHAPTER 18
ELECTRICAL
SPECIFICATIONS ((T)
product, (S) product,
(R) product, (A)
product) to CHAPTER
20 ELECTRICAL
SPECIFICATIONS
(TARGET VALUES)
((A2) product)
Applied to:
(5/8)