ATtiny20 Atmel Corporation, ATtiny20 Datasheet - Page 111

• Manufacturer Part Number: ATtiny20
• Manufacturer: Atmel Corporation

Specifications of ATtiny20

• Flash (kbytes): 2 Kbytes
• Pin Count: 14
• Max. Operating Frequency: 12 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 5
• Hardware Qtouch Acquisition: Yes
• Max I/o Pins: 12
• Ext Interrupts: 12
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.12
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 3
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

14.2.3
8235B–AVR–04/11
DIDR0 – Digital Input Disable Register 0
• Bit 6 – HLEV: Hysteresis Level
When enabled via the HSEL bit, the level of hysteresis can be set using the HLEV bit, as shown
in
Table 14-3.
• Bit 5 – ACLP
This bit is reserved for QTouch, always write as zero.
• Bit 4 – Res: Reserved Bit
This bit is reserved and will always read as zero.
• Bit 3 – ACCE
This bit is reserved for QTouch, always write as zero.
• Bit 2 – ACME: Analog Comparator Multiplexer Enable
When this bit is written logic one and the ADC is switched off (ADEN in ADCSRA is zero), the
ADC multiplexer selects the negative input to the Analog Comparator. When this bit is written
logic zero, AIN1 is applied to the negative input of the Analog Comparator. For a detailed
description of this bit, see
• Bit 1 – ACIRS1
This bit is reserved for QTouch, always write as zero.
• Bit 0 – ACIRS0
This bit is reserved for QTouch, always write as zero.
• Bits 2:1 – ADC2D, ADC1D: ADC 2/1 Digital input buffer disable
When this bit is written logic one, the digital input buffer on the AIN1/0 pin is disabled. The corre-
sponding PIN Register bit will always read as zero when this bit is set. When used as an analog
input but not required as a digital input the power consumption in the digital input buffer can be
reduced by writing this bit to logic one.
Bit
0x0D
Read/Write
Initial Value
Table
HSEL
0
1
14-3.
Selecting Level of Analog Comparator Hysteresis
ADC7D
R/W
7
0
HLEV
X
0
1
ADC6D
R/W
“Analog Comparator Multiplexed Input” on page
6
0
ADC5D
Hysteresis of Analog Comparator
Not enabled
20 mV
50 mV
R/W
5
0
ADC4D
R/W
4
0
ADC3D
R/W
3
0
ADC2D
R/W
2
0
ADC1D
R/W
1
0
109.
ADC0D
ATtiny20
R/W
0
0
DIDR0
111