ATtiny20 Atmel Corporation, ATtiny20 Datasheet - Page 85

• Manufacturer Part Number: ATtiny20
• Manufacturer: Atmel Corporation

Specifications of ATtiny20

• Flash (kbytes): 2 Kbytes
• Pin Count: 14
• Max. Operating Frequency: 12 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 5
• Hardware Qtouch Acquisition: Yes
• Max I/o Pins: 12
• Ext Interrupts: 12
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.12
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 3
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

12.7
8235B–AVR–04/11
Compare Match Output Unit
pare (1x) strobe bits in Normal mode. The OC1x Register keeps its value even when changing
between Waveform Generation modes.
Be aware that the COM1x[1:0] bits are not double buffered together with the compare value.
Changing the COM1x[1:0] bits will take effect immediately.
The Compare Output Mode (COM1x[1:0]) bits have two functions. The Waveform Generator
uses the COM1x[1:0] bits for defining the Output Compare (OC1x) state at the next compare
match. Secondly the COM1x[1:0] bits control the OC1x pin output source.
simplified schematic of the logic affected by the COM1x[1:0] bit setting. The I/O Registers, I/O
bits, and I/O pins in the figure are shown in bold. Only the parts of the general I/O port control
registers (DDR and PORT) that are affected by the COM1x[1:0] bits are shown. When referring
to the OC1x state, the reference is for the internal OC1x Register, not the OC1x pin. If a system
reset occur, the OC1x Register is reset to “0”.
Figure 12-5. Compare Match Output Unit, Schematic (non-PWM Mode)
The general I/O port function is overridden by the Output Compare (OC1x) from the Waveform
Generator if either of the COM1x[1:0] bits are set. However, the OC1x pin direction (input or out-
put) is still controlled by the Data Direction Register (DDR) for the port pin. The Data Direction
Register bit for the OC1x pin (DDR_OC1x) must be set as output before the OC1x value is visi-
ble on the pin. The port override function is generally independent of the Waveform Generation
mode, but there are some exceptions. See
Table 12-4 on page 100
COMnx1
COMnx0
FOCnx
clk
I/O
Waveform
Generator
for details.
D
D
D
PORT
DDR
OCnx
Table 12-2 on page
Q
Q
Q
99,
1
0
Table 12-3 on page 99
Figure 12-5
ATtiny20
OCnx
shows a
Pin
and
85