DSPIC33FJ128MC804-H/ML Microchip Technology, DSPIC33FJ128MC804-H/ML Datasheet - Page 227

• Manufacturer Part Number: DSPIC33FJ128MC804-H/ML
• Description: 16-bit DSC, 128KB Flash, Motor, CAN, DMA, 40 MIPS, NanoWatt 44 QFN 8x8x0.9mm TUB
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ128MC804-H/ML

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 9x10b/12b, D/A 6x16b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 140°C
• Package / Case: 44-QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

18.0
FIGURE 18-1:
© 2011 Microchip Technology Inc.
dsPIC33FJ32MC302/304, dsPIC33FJ64MCX02/X04 AND dsPIC33FJ128MCX02/X04
Note 1: This data sheet summarizes the features
SDOx
SCKx
SDIx
SSx
2: Some registers and associated bits
SERIAL PERIPHERAL
INTERFACE (SPI)
of
dsPIC33FJ64MCX02/X04
dsPIC33FJ128MCX02/X04
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to “Section 18. Serial
Peripheral Interface (SPI)” (DS70206)
of
Reference Manual”, which is available
from
(www.microchip.com).
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization”
this data sheet for device-specific register
and bit information.
Read SPIxBUF
the
Control
Sync
the
Transfer
the
SPI MODULE BLOCK DIAGRAM
“dsPIC33F/PIC24H
dsPIC33FJ32MC302/304,
Microchip
SPIxRXB
bit 0
SPIxBUF
SPIxSR
Control
Clock
Shift Control
SPIxTXB
web
family
Family
Transfer
Write SPIxBUF
and
site
of
in
Select
Edge
The Serial Peripheral Interface (SPI) module is a
synchronous serial interface useful for communicating
with other peripheral or microcontroller devices. These
peripheral devices can be serial EEPROMs, shift regis-
ters, display drivers, analog-to-digital converters, etc.
The SPI module is compatible with Motorola
SIOP.
Each SPI module consists of a 16-bit shift register,
SPIxSR (where x = 1 or 2), used for shifting data in and
out, and a buffer register, SPIxBUF. A control register,
SPIxCON, configures the module. Additionally, a status
register, SPIxSTAT, indicates status conditions.
The serial interface consists of 4 pins:
• SDIx (serial data input)
• SDOx (serial data output)
• SCKx (shift clock input or output)
• SSx (active-low slave select)
In Master mode operation, SCK is a clock output. In
Slave mode, it is a clock input.
16
Secondary
1:1 to 1:8
Prescaler
Internal Data Bus
1:1/4/16/64
Prescaler
Primary
F
SPIxCON1<1:0>
SPIxCON1<4:2>
Enable
Master Clock
DS70291E-page 227
CY
®
SPI and