CS8900-CQ3 Cirrus Logic, CS8900-CQ3 Datasheet - Page 67

no-image

CS8900-CQ3

Manufacturer Part Number
CS8900-CQ3
Description
Crystal LAN ISA Ethernet Controller
Manufacturer
Cirrus Logic
Datasheet
DS271PP3
4.4.20 Register 17: Bus Control
(BusCTL, Read/Write, Address: PacketPage base + 0116h)
BusCTL controls the operation of the ISA-bus interface.
010111
ResetRxDMA
DMAextend
UseSA
MemoryE
DMABurst
IOCHRDYE
RxDMAsize
EnableRQ
After reset, if no EEPROM is found by the CS8900A, then the register has the following initial state. If an EEPROM
is found, then the register’s initial value may be set by the EEPROM. See Section 3.3 on page 19.
Reset value is: 0000 0000 0001 0111
CS8900A
Crystal LAN™ ISA Ethernet Controller
EnableIRQ
F
7
Reset RxDMA
Register.
host sets this bit, the CS8900A does the following:
IOR
transfer mode DMA. Normal operation is demand mode DMA in which DMACKx cannot deas-
sert until after DMARQx deasserts, i.e. until a full ethernet frame is transferred. Single transfer
mode allows DMACKx to deassert between each DMA read.
CS8900A’s assigned Memory base address and the CHIPSEL pin is low (internal address de-
code).
see Section 4.9 on page 74.
For MEMCS16 pin to be enabled, the CS8900A must be in Memory Mode with the MemoryE
bit (Register 17, BusCTL, Bit A) set.
I/O Mode is always enabled.
transferred from the CS8900A to host memory. When set, each DMA access is limited to 28us,
after which time the CS8900A gives up the bus for 1.3us before making a new DMA request.
pedance. This allows external pull-up to force the output high. When clear, the CS8900A drives
IOCHRDY low to request additional time during I/O Read and Memory Read cycles. IOCHRDY
does not affect I/O Write, Memory Write, nor DMA Read.
DMA buffer size is 64 Kbytes. When clear, it is 16 Kbytes.
(Section 5.1). When cleared, the CS8900A will not generate any interrupts.
These bits provide an internal address used by the CS8900A to identify this as the Bus Control
When set, the RxDMA offset pointer at PacketPage base + 0026h is reset to zero. When the
When set, DMARQx goes inactive on the falling edge of IOR
When set, the MEMCS16 pin goes low whenever the address on SA bus [12..19] match the
When set, the CS8900A may operate in Memory Mode. When clear, Memory Mode is disabled.
When clear, the CS8900A performs continuous DMA until the receive frame is completely
When set, the CS8900A does not use the IOCHRDY output pin, and the pin is always high-im-
This bit determines the size of the receive DMA buffer (located in host memory). When set, the
When set, the CS8900A will generate an interrupt in response to an interrupt event
E
When clear, MEMCS16 is driven low whenever CHIPSEL goes low. (external address decode).
6
N
-1
. See Switching Characteristics, DMA Read, t
RxDMA size
1.Terminates the current receive DMA activity, if any.
2.Clears all internal receive buffers.
3.Zeroes the RxDMA offset pointer.
D
5
CIRRUS LOGIC PRODUCT DATA SHEET
IOCH RDYE
C
4
DMABurst
B
3
010111
DMAR5
MemoryE
A
2
. Setting this bit also enables single
N
instead of the rising edge of
UseSA
1
9
DMAextend
0
8
67

Related parts for CS8900-CQ3