AT91RM3400-DK Atmel, AT91RM3400-DK Datasheet - Page 104
![KIT DEV FOR AT91RM3400](/photos/9/21/92145/at91rm3400-dk__bottom__sml.jpg)
AT91RM3400-DK
Manufacturer Part Number
AT91RM3400-DK
Description
KIT DEV FOR AT91RM3400
Manufacturer
Atmel
Series
AT91SAM Smart ARMr
Type
MCUr
Datasheets
1.AT91RM3400-DK.pdf
(461 pages)
2.AT91RM3400-DK.pdf
(2 pages)
3.AT91RM3400-DK.pdf
(25 pages)
Specifications of AT91RM3400-DK
Contents
Evaluation Board, Software and Documentation
Processor To Be Evaluated
AT91RM3400
Data Bus Width
32 bit
Interface Type
RS-232, USB
For Use With/related Products
AT91RM3400
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 104 of 461
- Download datasheet (6Mb)
Functional Description
Interrupt Source
Control
Interrupt Source Mode
Interrupt Source
Enabling
Interrupt Clearing and
Setting
Interrupt Status
104
AT91RM3400
The Advanced Interrupt Controller independently programs each interrupt source. The SRC-
TYPE field of the corresponding AIC_SMR (Source Mode Register) selects the interrupt
condition of each source.
The internal interrupt sources wired on the interrupt outputs of the embedded peripherals can
be programmed either in level-sensitive mode or in edge-triggered mode. The active level of
the internal interrupts is not important for the user.
The external interrupt sources can be programmed either in high level-sensitive or low level-
sensitive modes, or in positive edge-triggered or negative edge-triggered modes.
Each interrupt source, including the FIQ in source 0, can be enabled or disabled by using the
command registers; AIC_IECR (Interrupt Enable Command Register) and AIC_IDCR (Inter-
rupt Disable Command Register). This set of registers conducts enabling or disabling in one
instruction. The interrupt mask can be read in the AIC_IMR register. A disabled interrupt does
not affect servicing of other interrupts.
All interrupt sources programmed to be edge-triggered (including the FIQ in source 0) can be
individually set or cleared by writing respectively the AIC_ISCR and AIC_ICCR registers.
Clearing or setting interrupt sources programmed in level-sensitive mode has no effect.
The clear operation is perfunctory, as the software must perform an action to reinitialize the
“memorization” circuitry activated when the source is programmed in edge-triggered mode.
However, the set operation is available for auto-test or software debug purposes. It can also
be used to execute an AIC-implementation of a software interrupt.
The AIC features an automatic clear of the current interrupt when the AIC_IVR (Interrupt Vec-
tor Register) is read. Only the interrupt source being detected by the AIC as the current
interrupt is affected by this operation. (See “Priority Controller” on page 107.) The automatic
clear reduces the operations required by the interrupt service routine entry code to reading the
AIC_IVR. Note that the automatic interrupt clear is disabled if the interrupt source has the Fast
Forcing feature enabled as it is considered uniquely as a FIQ source. (For further details, See
“Fast Forcing” on page 111.)
The automatic clear of the interrupt source 0 is performed when AIC_FVR is read.
For each interrupt, the AIC operation originates in AIC_IPR (Interrupt Pending Register) and
its mask in AIC_IMR (Interrupt Mask Register). AIC_IPR enables the actual activity of the
sources, whether masked or not.
The AIC_ISR register reads the number of the current interrupt (see “Priority Controller” on
page 107) and the register AIC_CISR gives an image of the signals nIRQ and nFIQ driven on
the processor.
Each status referred to above can be used to optimize the interrupt handling of the systems.
1790A–ATARM–11/03
Related parts for AT91RM3400-DK
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ATSTK600](/photos/9/20/92038/atstk600_tmb.jpg)
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
![U641B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
![U4082B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
![U4089B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
![U4255BM-M](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
![U4089B-P](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
![TDA4470](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
![ATF22V10B-25PC](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
![AT89C51ED2-IM](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
![AT24C01](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: