ST72C334J4T6 STMicroelectronics, ST72C334J4T6 Datasheet - Page 48

• Manufacturer Part Number: ST72C334J4T6
• Description: MCU 8BIT FLASH SPI SCI 44TQFP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72C334J4T6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 3.2 V ~ 5.5 V
• Data Converters: A/D 6x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Processor Series: ST72C3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 4 bit
• Operating Supply Voltage: 3.2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7C334-INDART, ST7MDT2-EPB2/US
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-4838

ST72334J/N, ST72314J/N, ST72124J
MISCELLANEOUS REGISTERS (Cont’d)
MISCELLANEOUS REGISTER 2 (MISCR2)
Read /Write
Reset Value: 0000 0000 (00h)
Bit 7:6 = Reserved Must always be cleared
Bit 5:4 = BC[1:0] Beep control
These 2 bits select the PF1 pin beep capability.
The beep output signal is available in ACTIVE-
HALT mode but has to be disabled to reduce the
consumption.
Bit 3:2 = Reserved Must always be cleared
Bit 1 = SSM SS mode selection
It is set and cleared by software.
0: Normal mode - SS uses information coming
from the SS pin of the SPI.
1: I/O mode, the SPI uses the information stored
into bit SSI.
Bit 0 = SSI SS internal mode
This bit replaces pin SS of the SPI when bit SSM is
set to 1. (see SPI description). It is set and cleared
by software.
Table 10. Miscellaneous Register Map and Reset Values
48/153
Address
7
-
(Hex.)
0020h
0040h
Beep mode with f
~500-Hz
~1-KHz
~2-KHz
-
MISCR1
Reset Value
MISCR2
Reset Value
BC1
Register
Label
Off
BC0
~50% duty cycle
OSC
Beep signal
=16MHz
Output
IS11
-
7
0
0
-
IS10
SSM
6
0
0
BC1 BC0
0
0
1
1
SSI
0
0
1
0
1
MCO
BC1
5
0
0
IS21
BC0
4
0
0
IS20
3
0
0
CP1
2
0
0
SSM
CP0
1
0
0
SMS
SSI
0
0
0