ST72C334J4T6 STMicroelectronics, ST72C334J4T6 Datasheet - Page 61

• Manufacturer Part Number: ST72C334J4T6
• Description: MCU 8BIT FLASH SPI SCI 44TQFP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72C334J4T6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 3.2 V ~ 5.5 V
• Data Converters: A/D 6x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Processor Series: ST72C3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 4 bit
• Operating Supply Voltage: 3.2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7C334-INDART, ST7MDT2-EPB2/US
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-4838

16-BIT TIMER (Cont’d)
Notes:
1. After a processor write cycle to the OC i HR reg-
2. If the OC i E bit is not set, the OCMP i pin is a
3. When the timer clock is f
4. The output compare functions can be used both
5. The value in the 16-bit OC
Figure 37. Output Compare Block Diagram
16-bit
ister, the output compare function is inhibited
until the OC i LR register is also written.
general I/O port and the OLVL i bit will not
appear when a match is found but an interrupt
could be generated if the OCIE bit is set.
OCMP i are set while the counter value equals
the OC i R register value (see
62). This behaviour is the same in OPM or
PWM mode.
When the timer clock is f
external clock mode, OCF i and OCMP i are set
while the counter value equals the OC i R regis-
ter value plus 1 (see
for generating external events on the OCMP i
pins even if the input capture mode is also
used.
OLV i bit should be changed after each suc-
cessful comparison in order to control an output
waveform or establish a new elapsed timeout.
16 BIT FREE RUNNING
OC1R Register
OUTPUT COMPARE
16-bit
CIRCUIT
OC2R Register
COUNTER
16-bit
Figure 39 on page
CPU
i
R register and the
CPU
Figure 38 on page
/4, f
/2, OCF i and
OC1E
CPU
OCIE
OC2E
OCF1
/8 or in
62).
FOLV2 FOLV1
Forced Compare Output capability
When the FOLV i bit is set by software, the OLVL i
bit is copied to the OCMP i pin. The OLV i bit has to
be toggled in order to toggle the OCMP i pin when
it is enabled (OC i E bit=1). The OCF i bit is then not
set by hardware, and thus no interrupt request is
generated.
FOLVL i bits have no effect in either One-Pulse
mode or PWM mode.
(Control Register 2) CR2
(Control Register 1) CR1
OCF2
CC1
(Status Register) SR
OLVL2
ST72334J/N, ST72314J/N, ST72124J
CC0
0
0
OLVL1
0
Latch
Latch
1
2
OCMP2
OCMP1
Pin
Pin
61/153