TMP86FH46ANG(Z) Toshiba, TMP86FH46ANG(Z) Datasheet - Page 100

• Manufacturer Part Number: TMP86FH46ANG(Z)
• Description: IC MCU 8BIT FLASH 16KB 42-SDIP
• Manufacturer: Toshiba
• Series: TLCS-870/Cr

Specifications of TMP86FH46ANG(Z)

• Core Processor: 870/C
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: LED, PWM, WDT
• Number Of I /o: 33
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 42-SDIP (0.600", 15.24mm)
• Processor Series: TLCS-870
• Core: 870/C
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SIO, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: BMSKTOPAS86FH47(AND), BM1040R0A, BMP86A100010A, BMP86A100010B, BMP86A200010B, BMP86A200020A, BMP86A300010A, BMP86A300020A, BMP86A300030A, SW89CN0-ZCC, SW00MN0-ZCC
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: BM1401W0A-G - FLASH WRITER ON-BOARD PROGRAMTMP86C909XB - EMULATION CHIP FOR TMP86F SDIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: TMP86FH46ANGZ

9.1 Configuration
TimerCounter 4 Timer Register
TimerCounter 4 Control Register
PWREG4
TTREG4
(001BH)
(0019H)
(0017H)
TC4CR
(TTREG4 and PWREG4).
R/W
R/W
The TimerCounter 4 is controlled by the TimerCounter 4 control register (TC4CR) and two 8-bit timer registers
Note 1: Do not change the timer register (TTREG4) setting while the timer is running.
Note 2: Do not change the timer register (PWREG4) setting in the operating mode except the 8-bit and 16-bit PWM modes while
Note 1: fc: High-frequency clock [Hz] fs: Low-frequency clock [Hz]
Note 2: Do not change the TC4M, TC4CK and TFF4 settings while the timer is running.
Note 3: To stop the timer operation (TC4S= 1 → 0), do not change the TC4M, TC4CK and TFF4 settings.
Note 4: When TC4M= 1** (upper byte in the 16-bit mode), the source clock becomes the TC4 overflow signal regardless of the
Note 5: To use the TimerCounter in the 16-bit mode, select the operating mode by programming TC4M, where TC3CR<TC3 M>
TC4CK
TC4M
TC4S
TFF4
the timer is running.
To start the timer operation (TC4S= 0 → 1), TC4M, TC4CK and TFF4 can be programmed.
TC3CK setting.
must be set to 011.
TFF4
7
7
7
Timer F/F4 control
Operating clock selection [Hz]
TC4 start control
TC4M operating mode select
6
6
6
TC4CK
5
5
5
4
4
4
000:
001:
010:
011:
100:
101:
110:
111:
TC4S
0:
1:
0:
1:
3
3
3
000
001
010
100
101
011
110
111
Clear
Set
Operation stop and counter clear
Operation start
8-bit timer/event counter mode
8-bit programmable divider output (PDO) mode
8-bit pulse width modulation (PWM) output mode
Reserved
16-bit timer/event counter mode
Warm-up counter mode
16-bit pulse width modulation (PWM) output mode
16-bit PPG mode
2
2
2
Page 86
DV7CK = 0
TC4M
NORMAL1/2, IDLE1/2 mode
1
1
1
fc/2
fc/2
fc/2
fc/2
fc/2
fs
fc
11
7
5
3
0
0
0
(Initial value: 1111 1111)
(Initial value: 1111 1111)
(Initial value: 0000 0000)
TC4 pin input
DV7CK = 1
fs/2
fc/2
fc/2
fc/2
fc/2
fs
fc
3
7
5
3
SLEEP1/2
SLOW1/2
mode
fs/2
fs
–
–
–
–
–
3
TMP86FH46ANG
R/W
R/W
R/W
R/W