TMP86FH46ANG(Z) Toshiba, TMP86FH46ANG(Z) Datasheet - Page 29

• Manufacturer Part Number: TMP86FH46ANG(Z)
• Description: IC MCU 8BIT FLASH 16KB 42-SDIP
• Manufacturer: Toshiba
• Series: TLCS-870/Cr

Specifications of TMP86FH46ANG(Z)

• Core Processor: 870/C
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: LED, PWM, WDT
• Number Of I /o: 33
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 42-SDIP (0.600", 15.24mm)
• Processor Series: TLCS-870
• Core: 870/C
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SIO, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: BMSKTOPAS86FH47(AND), BM1040R0A, BMP86A100010A, BMP86A100010B, BMP86A200010B, BMP86A200020A, BMP86A300010A, BMP86A300020A, BMP86A300030A, SW89CN0-ZCC, SW00MN0-ZCC
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: BM1401W0A-G - FLASH WRITER ON-BOARD PROGRAMTMP86C909XB - EMULATION CHIP FOR TMP86F SDIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: TMP86FH46ANGZ

System Control Register 1
System Control Register 2
SYSCR1
SYSCR2
(0038H)
(0039H)
Note 1: Always set RETM to “0” when transiting from NORMAL mode to STOP mode. Always set RETM to “1” when transiting
Note 2: When STOP mode is released with
Note 3: fc: High-frequency clock [Hz], fs: Low-frequency clock [Hz], *; Don’t care
Note 4: Bits 1 in SYSCR1 are read as undefined data when a read instruction is executed.
Note 5: As the hardware becomes STOP mode under OUTEN = “0”, input value is fixed to “0”; therefore it may cause external
Note 6: When the key-on wakeup is used, RELM should be set to "1".
Note 7: Port P20 is used as
Note 8: The warmig-up time should be set correctly for using oscillator.
Note 1: A reset is applied if both XEN and XTEN are cleared to “0”, XEN is cleared to “0” when SYSCK = “0”, or XTEN is cleared
Note 2: *: Don’t care, TG: Timing generator, *; Don’t care
Note 3: Bits 3, 1 and 0 in SYSCR2 are always read as undefined value.
Note 4: Do not set IDLE and TGHALT to “1” simultaneously.
Note 5: Because returning from IDLE0/SLEEP0 to NORMAL1/SLOW1 is executed by the asynchronous internal clock, the period
Note 6: When IDLE1/2 or SLEEP1/2 mode is released, IDLE is automatically cleared to “0”.
Note 7: When IDLE0 or SLEEP0 mode is released, TGHALT is automatically cleared to “0”.
from SLOW mode to STOP mode.
interrupt request on account of falling edge.
High-Z mode.
to “0” when SYSCK = “1”.
of IDLE0/SLEEP0 mode might be shorter than the period setting by TBTCR<TBTCK>.
STOP
TGHALT
XEN
SYSCK
OUTEN
XTEN
STOP
RELM
RETM
IDLE
7
7
XEN
WUT
RELM
XTEN
High-frequency oscillator control
Low-frequency oscillator control
Main system clock select
(Write)/main system clock moni-
tor (Read)
CPU and watchdog timer control
(IDLE1/2 and SLEEP1/2 modes)
TG control (IDLE0 and SLEEP0
modes)
6
6
STOP mode start
Release method for STOP
mode
Operating mode after STOP
mode
Port output during STOP mode
Warm-up time at releasing
STOP mode
SYSCK
STOP
RETM
5
5
pin. Therefore, when stop mode is started, OUTEN does not affect to P20, and P20 becomes
OUTEN
IDLE
4
4
RESET
0: CPU core and peripherals remain active
1: CPU core and peripherals are halted (Start STOP mode)
0: Edge-sensitive release
1: Level-sensitive release
0: Return to NORMAL1/2 mode
1: Return to SLOW1 mode
0: High impedance
1: Output kept
0: Turn off oscillation
1: Turn on oscillation
0: Turn off oscillation
1: Turn on oscillation
0: High-frequency clock (NORMAL1/NORMAL2/IDLE1/IDLE2)
1: Low-frequency clock (SLOW1/SLOW2/SLEEP1/SLEEP2)
0: CPU and watchdog timer remain active
1: CPU and watchdog timer are stopped (Start IDLE1/2 and SLEEP1/2 modes)
0: Feeding clock to all peripherals from TG
1: Stop feeding clock to peripherals except TBT from TG.
3
3
pin input, a return is made to NORMAL1 regardless of the RETM contents.
000
010
100
110
*01
*11
(Start IDLE0 and SLEEP0 modes)
Page 15
TGHALT
WUT
2
2
Return to NORMAL mode
3 x 2
3 x 2
3 x 2
1
1
2
2
2
16
14
10
16
14
10
/fc
/fc
/fc
/fc
/fc
/fc
0
0
(Initial value: 0000 000*)
(Initial value: 1000 *0**)
Return to SLOW mode
3 x 2
3 x 2
3 x 2
2
2
2
13
6
6
/fs
/fs
13
/fs
6
6
TMP86FH46ANG
/fs
/fs
/fs
R/W
R/W
R/W
R/W
R/W
R/W
R/W