TMP86FH46ANG(Z) Toshiba, TMP86FH46ANG(Z) Datasheet - Page 175

• Manufacturer Part Number: TMP86FH46ANG(Z)
• Description: IC MCU 8BIT FLASH 16KB 42-SDIP
• Manufacturer: Toshiba
• Series: TLCS-870/Cr

Specifications of TMP86FH46ANG(Z)

• Core Processor: 870/C
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: LED, PWM, WDT
• Number Of I /o: 33
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 42-SDIP (0.600", 15.24mm)
• Processor Series: TLCS-870
• Core: 870/C
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SIO, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: BMSKTOPAS86FH47(AND), BM1040R0A, BMP86A100010A, BMP86A100010B, BMP86A200010B, BMP86A200020A, BMP86A300010A, BMP86A300020A, BMP86A300030A, SW89CN0-ZCC, SW00MN0-ZCC
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: BM1401W0A-G - FLASH WRITER ON-BOARD PROGRAMTMP86C909XB - EMULATION CHIP FOR TMP86F SDIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: TMP86FH46ANGZ

Table 15-7 Flash Memory Erasing Mode
BOOT
ROM
15.6.1 Flash Memory Erasing Mode (Operating command: F0H)
Note 1: “xxH × 3” indicates that the device enters the halt condition after transmitting 3 bytes of xxh.
Note 2: Refer to " 15.13 Specifying the Erasure Area ".
Note 3: Refer to " 15.8 Checksum (SUM) ".
Note 4: Refer to " 15.10 Passwords ".
Note 5: Do not transmit the password string for a blank product.
Note 6: When a password error occurs, TMP86FH46ANG stops UART communication and enters the halt mode. Therefore, when
Note 7: If an error occurs during transfer of a password address or a password string, TMP86FH46ANG stops UART communica-
1st byte
2nd byte
3rd byte
4th byte
5th byte
6th byte
7th byte
8th byte
9th byte
10th byte
11th byte
12th byte
13th byte
14th byte
15th byte
m’th byte
n’th - 2 byte
n’th - 1 byte
n’th byte
n’th + 1 byte
:
Table 15-7 shows the flash memory erasing mode.
Transfer Byte
Description of the flash memory erasing mode
a password error occurs, initialize TMP86FH46ANG by the
tion and enters the halt condition. Therefore, when a password error occurs, initialize TMP86FH46ANG by the
and reactivate the serial PROM mode.
1. The 1st through 4th bytes of the transmitted and received data contain the same data as in the flash
memory writing mode.
Matching data (5AH)
-
Baud rate change data (Table 15-4)
-
Operation command data (F0H)
-
Password count storage address bit
15 to 08 (Note 4, 5)
Password count storage address bit
07 to 00 (Note 4, 5)
Password comparison start address
bit 15 to 08 (Note 4, 5)
Password comparison start address
bit 07 to 00 (Note 4, 5)
Password string (Note 4, 5)
-
Erase area specification (Note 2)
-
-
(Wait for the next operation command
data)
Transfer Data from the External
Controller to TMP86FH46ANG
Page 161
9600 bps
9600 bps
9600 bps
9600 bps
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
RESET
Baud Rate
pin and reactivate the serial PROM mode.
- (Automatic baud rate adjustment)
OK: Echo back data (5AH)
Error: No data transmitted
-
OK: Echo back data
Error: A1H × 3, A3H × 3, 62H × 3 (Note 1)
-
OK: Echo back data (F0H)
Error: A1H × 3, A3H × 3, 63H × 3 (Note 1)
-
OK: Nothing transmitted
Error: Nothing transmitted
-
OK: Nothing transmitted
Error: Nothing transmitted
-
OK: Nothing transmitted
Error: Nothing transmitted
-
OK: Nothing transmitted
Error: Nothing transmitted)
-
OK: Nothing transmitted
Error: Nothing transmitted
-
OK: Checksum (Upper byte) (Note 3)
Error: Nothing transmitted
OK: Checksum (Lower byte) (Note 3)
Error: Nothing transmitted
-
Transfer Data from TMP86FH46ANG to
the External Controller
TMP86FH46ANG
RESET
pin