TMP86FH46ANG(Z) Toshiba, TMP86FH46ANG(Z) Datasheet - Page 37

• Manufacturer Part Number: TMP86FH46ANG(Z)
• Description: IC MCU 8BIT FLASH 16KB 42-SDIP
• Manufacturer: Toshiba
• Series: TLCS-870/Cr

Specifications of TMP86FH46ANG(Z)

• Core Processor: 870/C
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: LED, PWM, WDT
• Number Of I /o: 33
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 42-SDIP (0.600", 15.24mm)
• Processor Series: TLCS-870
• Core: 870/C
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SIO, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: BMSKTOPAS86FH47(AND), BM1040R0A, BMP86A100010A, BMP86A100010B, BMP86A200010B, BMP86A200020A, BMP86A300010A, BMP86A300020A, BMP86A300030A, SW89CN0-ZCC, SW00MN0-ZCC
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: BM1401W0A-G - FLASH WRITER ON-BOARD PROGRAMTMP86C909XB - EMULATION CHIP FOR TMP86F SDIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: TMP86FH46ANGZ

2.2.4.3
timer control register (TBTCR). The following status is maintained during IDLE0 and SLEEP0 modes.
IDLE0 and SLEEP0 modes (IDLE0, SLEEP0)
IDLE0 and SLEEP0 modes are controlled by the system control register 2 (SYSCR2) and the time base
Note: Before starting IDLE0 or SLEEP0 mode, be sure to stop (Disable) peripherals.
1. Timing generator stops feeding clock to peripherals except TBT.
2. The data memory, CPU registers, program status word and port output latches are all held in the
3. The program counter holds the address 2 ahead of the instruction which starts IDLE0 and
status in effect before IDLE0 and SLEEP0 modes were entered.
SLEEP0 modes.
(Normal release mode)
Figure 2-12 IDLE0 and SLEEP0 Modes
No
No
No
No
CPU and WDT are halted
Execution of the instruction
which follows the IDLE0,
Page 23
Starting IDLE0, SLEEP0
Stopping peripherals
Interrupt processing
SLEEP0 modes start
modes by instruction
TBTCR<TBTEN>
by instruction
TBT interrupt
source clock
Reset input
IMF = "1"
instruction
enable
falling
= "1"
edge
TBT
Yes
Yes
No
Yes
Yes (Interrupt release mode)
Yes
Reset
TMP86FH46ANG