TMP86FH46ANG(Z) Toshiba, TMP86FH46ANG(Z) Datasheet - Page 161

• Manufacturer Part Number: TMP86FH46ANG(Z)
• Description: IC MCU 8BIT FLASH 16KB 42-SDIP
• Manufacturer: Toshiba
• Series: TLCS-870/Cr

Specifications of TMP86FH46ANG(Z)

• Core Processor: 870/C
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: LED, PWM, WDT
• Number Of I /o: 33
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 42-SDIP (0.600", 15.24mm)
• Processor Series: TLCS-870
• Core: 870/C
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SIO, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: BMSKTOPAS86FH47(AND), BM1040R0A, BMP86A100010A, BMP86A100010B, BMP86A200010B, BMP86A200020A, BMP86A300010A, BMP86A300020A, BMP86A300030A, SW89CN0-ZCC, SW00MN0-ZCC
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: BM1401W0A-G - FLASH WRITER ON-BOARD PROGRAMTMP86C909XB - EMULATION CHIP FOR TMP86F SDIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: TMP86FH46ANGZ

14.2.3 Chip Erase (All Erase)
14.2.4 Product ID Entry
14.2.5 Product ID Exit
14.2.6 Read Protect
Note: The value at address F002H (flash size) depends on the size of flash memory incorporated in each product. For example, if
be executed until the erase operation is completed. To check the completion of the erase operation, perform
read operations repeatedly for data polling until the same data is read twice from the same address in the flash
memory. During the erase operation, any consecutive attempts to read from the same address is reversed bit 6
of the data (toggling between 0 and 1). After the chip is erased, all bytes contain FFH.
read protection status can be read from the flash memory.
the flash memory cannot be read in the parallel PROM mode. In the serial PROM mode, the flash write and
RAM loader commands cannot be executed.
or not the read protection is enabled can be checked by reading FF7FH in the Product ID mode. For details, see
Table 14-2.
be executed until this operation is completed. To check the completion of the read protect operation, perform
read operations repeatedly for data polling until the same data is read twice from the same address in the flash
memory. During the read protect operation, any attempts to read from the same address is reversed bit 6 of the
data (toggling between 0 and 1).
This command erases the entire flash memory in approximately 30 ms. The next command sequence cannot
This command activates the Product ID mode. In the Product ID mode, the vendor ID, the flash ID, and the
the product has 60-kbyte flash memory, "0EH" is read from address F002H.
This command is used to exit the Product ID mode.
This command enables the read protection setting in the flash memory. When the read protection is enabled,
It takes a maximum of 40 µs to set read protection in the flash memory. The next command sequence cannot
To disable the read protection setting, it is necessary to execute the chip erase command sequence. Whether
Table 14-2 Values To Be Read in the Product ID Mode
Address
F000H
F001H
F002H
FF7FH
Read protection status
Flash macro ID
Vendor ID
Flash size
Meaning
Page 147
98H
41H
0EH:
0BH:
07H:
05H:
03H:
01H:
00H:
FFH:
Other than FFH: Read protection enabled
60 kbytes
48 kbytes
32 kbytes
24 kbytes
16 kbytes
8 kbytes
4 kbytes
Read protection disabled
Read Value
TMP86FH46ANG