TMP86FH46ANG(Z) Toshiba, TMP86FH46ANG(Z) Datasheet - Page 31

• Manufacturer Part Number: TMP86FH46ANG(Z)
• Description: IC MCU 8BIT FLASH 16KB 42-SDIP
• Manufacturer: Toshiba
• Series: TLCS-870/Cr

Specifications of TMP86FH46ANG(Z)

• Core Processor: 870/C
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: LED, PWM, WDT
• Number Of I /o: 33
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 42-SDIP (0.600", 15.24mm)
• Processor Series: TLCS-870
• Core: 870/C
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SIO, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: BMSKTOPAS86FH47(AND), BM1040R0A, BMP86A100010A, BMP86A100010B, BMP86A200010B, BMP86A200020A, BMP86A300010A, BMP86A300020A, BMP86A300030A, SW89CN0-ZCC, SW00MN0-ZCC
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: BM1401W0A-G - FLASH WRITER ON-BOARD PROGRAMTMP86C909XB - EMULATION CHIP FOR TMP86F SDIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: TMP86FH46ANGZ

STOP pin
XOUT pin
STOP pin
XOUT pin
Example 2 :Starting STOP mode from NORMAL mode with an INT5 interrupt.
Example :Starting STOP mode from NORMAL mode
PINT5:
SINT5:
STOP mode started
by the program.
(2)
NORMAL
operation
cations where a relatively short program is executed repeatedly at periodic intervals. This periodic
signal (for example, a clock from a low-power consumption oscillator) is input to the
the edge-sensitive release mode, STOP mode is started even when the
Do not use any STOP5 to STOP2 pin input for releasing STOP mode in edge-sensitive release mode.
NORMAL
operation
Note 1: Even if the
Note 2: In this case of changing to the level-sensitive mode from the edge-sensitive mode, the release
Edge-sensitive release mode (RELM = “0”)
In this mode, STOP mode is released by a rising edge of the
TEST
JRS
LD
DI
SET
RETI
DI
LD
mode is not switched until a rising edge of the
Figure 2-7 Level-sensitive Release Mode
Figure 2-8 Edge-sensitive Release Mode
(P2PRD). 0
F, SINT5
(SYSCR1), 01010000B
(SYSCR1). 7
(SYSCR1), 10010000B
STOP
Confirm by program that the
STOP pin input is low and start
STOP mode.
operation
STOP
pin input is low after warm-up start, the STOP mode is not restarted.
operation
STOP
Page 17
; To reject noise, STOP mode does not start if
; Sets up the level-sensitive release mode.
; IMF ← 0
; Starts STOP mode
; IMF ← 0
; Starts after specified to the edge-sensitive release mode
port P20 is at high
V
IH
Warm up
STOP mode is released by the hardware at the rising
edge of STOP pin input.
STOP
V
IH
STOP mode is released by the hardware.
Warm up
pin input is detected.
NORMAL
operation
Always released if the STOP
pin input is high.
STOP
pin input. This is used in appli-
STOP
NORMAL
operation
operation
STOP
pin input is high level.
TMP86FH46ANG
STOP
pin. In