TMP86FH46ANG(Z) Toshiba, TMP86FH46ANG(Z) Datasheet - Page 204

• Manufacturer Part Number: TMP86FH46ANG(Z)
• Description: IC MCU 8BIT FLASH 16KB 42-SDIP
• Manufacturer: Toshiba
• Series: TLCS-870/Cr

Specifications of TMP86FH46ANG(Z)

• Core Processor: 870/C
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: LED, PWM, WDT
• Number Of I /o: 33
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 42-SDIP (0.600", 15.24mm)
• Processor Series: TLCS-870
• Core: 870/C
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SIO, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: BMSKTOPAS86FH47(AND), BM1040R0A, BMP86A100010A, BMP86A100010B, BMP86A200010B, BMP86A200020A, BMP86A300010A, BMP86A300020A, BMP86A300030A, SW89CN0-ZCC, SW00MN0-ZCC
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: BM1401W0A-G - FLASH WRITER ON-BOARD PROGRAMTMP86C909XB - EMULATION CHIP FOR TMP86F SDIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: TMP86FH46ANGZ

17.1 Absolute Maximum Ratings
17.3 DC Characteristics
Hysteresis voltage
Input current
Input resistance
Output leakage current
Output high voltage
Output low voltage
Output low curren
Supply current in
NORMAL1, 2 modes
Supply current in IDLE
0, 1, 2 modes
Supply current in
SLOW1 mode
Supply current in
SLEEP1 mode
Supply current in
SLEEP0 mode
Supply current in
STOP mode
Peak current for
SLOW1 mode
(Note5,6)
Parameter
Note 1: Typical values show those at Topr = 25°C and V
Note 2: Input current I
Note 3: I
Note 4: The supply currents of SLOW2 and SLEEP2 modes are equivalent to those of IDLE0, IDLE1 and IDLE2 modes.
Note 5: When a program is executing in the flash memory or when data is being read from the flash memory, the flash memory
Note 6: When designing the power supply, make sure that peak currents can be supplied. In SLOW1 mode, the difference
operates in an intermittent manner, causing peak currents in the operation current, as shown in Figure 17-1.
In this case, the supply current I
peak current and MCU current.
between the peak current and the average current becomes large.
DD
does not include I
Symbol
I
DDP-P
R
V
I
I
V
V
I
I
I
I
I
LO1
LO2
IN1
IN2
IN3
OL
DD
HS
IN2
OH
OL
IN1
Hysteresis input
TEST
Sink open drain, tri–state port
RESET
RESET
Sink open drain port
Tri–state port
Tri–state port
Except XOUT, P3, P5
High current port
(P3, P5 Port)
: The current through pull-down resistor is not included.
REF
,
pull–up
STOP
.
Pins
DD
(in NORMAL1, NORMAL2 and SLOW1 modes) is defined as the sum of the average
V
V
V
V
V
V
V
V
V
fc = 16 MHz
fs = 32.768 kHz
V
V
fs = 32.768 kHz
V
V
V
V
Page 190
DD
DD
DD
DD
DD
DD
DD
DD
IN
DD
IN
DD
IN
DD
DD
DD
= 5.3 V/0.2 V
= 2.8 V/0.2 V
= 5.3 V/0.2 V
= 5.5 V, V
= 5.5 V, V
= 5.5 V, V
= 5.5 V, V
= 4.5 V, I
= 4.5 V, I
= 4.5 V, V
= 5.5 V
= 3.0 V
= 5.5 V
= 5.5 V
= 3.0 V
= 5 V.
OH
OL
IN
IN
OUT
OUT
OL
= 1.6 mA
= 5.5 V/0 V
= 0 V
= -0.7 mA
= 1.0 V
Condition
= 5.5 V
= 5.5 V/0 V
When a program
operates on flash
memory (Note5,6)
When a program
operates on RAM
(FLSSTB<FSTB>=0)
When a program
operates on flash
memory (Note5,6)
When a program
operates on RAM
(FLSSTB<FSTB>=0)
When a program
operates on RAM
(FLSSTB<FSTB>=1)
Min
100
4.1
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
(V
SS
= 0 V, Topr = -40 to 85 °C)
Typ.
12.6
20.0
14.0
220
0.9
6.5
4.5
9.0
5.0
4.0
0.5
20
10
–
–
–
–
–
2
TMP86FH46ANG
50.0
28.0
15.0
13.0
Max
450
0.4
6.5
±2
±2
18
10
–
2
–
–
9
–
–
–
Unit
mA
mA
mA
µA
kΩ
µA
µA
V
V