MC68HC711E20CFN2

Manufacturer Part NumberMC68HC711E20CFN2
DescriptionIC MCU 20K 2MHZ OTP 52-PLCC
ManufacturerFreescale Semiconductor
SeriesHC11
MC68HC711E20CFN2 datasheets
 

Specifications of MC68HC711E20CFN2

Core ProcessorHC11Core Size8-Bit
Speed2MHzConnectivitySCI, SPI
PeripheralsPOR, WDTNumber Of I /o38
Program Memory Size20KB (20K x 8)Program Memory TypeOTP
Eeprom Size512 x 8Ram Size768 x 8
Voltage - Supply (vcc/vdd)4.5 V ~ 5.5 VData ConvertersA/D 8x8b
Oscillator TypeInternalOperating Temperature-40°C ~ 85°C
Package / Case52-PLCCLead Free Status / RoHS StatusContains lead / RoHS non-compliant
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
Page 101
102
Page 102
103
Page 103
104
Page 104
105
Page 105
106
Page 106
107
Page 107
108
Page 108
109
Page 109
110
Page 110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
Page 109/242

Download datasheet (2Mb)Embed
PrevNext
7.5.2 Address-Mark Wakeup
The serial characters in this type of wakeup consist of seven (eight if M = 1) information bits and an MSB,
which indicates an address character (when set to 1, or mark). The first character of each message is an
addressing character (MSB = 1). All receivers in the system evaluate this character to determine if the
remainder of the message is directed toward this particular receiver. As soon as a receiver determines
that a message is not intended for it, the receiver activates the RWU function by using a software write to
set the RWU bit. Because setting RWU inhibits receiver-related flags, there is no further software
overhead for the rest of this message.
When the next message begins, its first character has its MSB set, which automatically clears the RWU
bit and enables normal character reception. The first character whose MSB is set is also the first character
to be received after wakeup because RWU gets cleared before the stop bit for that frame is serially
received. This type of wakeup allows messages to include gaps of idle time, unlike the idle-line method,
but there is a loss of efficiency because of the extra bit time for each character (address bit) required for
all characters.
7.6 SCI Error Detection
Three error conditions – SCDR overrun, received bit noise, and framing – can occur during generation of
SCI system interrupts. Three bits (OR, NF, and FE) in the serial communications status register (SCSR)
indicate if one of these error conditions exists.
The overrun error (OR) bit is set when the next byte is ready to be transferred from the receive shift
register to the SCDR and the SCDR is already full (RDRF bit is set). When an overrun error occurs, the
data that caused the overrun is lost and the data that was already in SCDR is not disturbed. The OR is
cleared when the SCSR is read (with OR set), followed by a read of the SCDR.
The noise flag (NF) bit is set if there is noise on any of the received bits, including the start and stop bits.
The NF bit is not set until the RDRF flag is set. The NF bit is cleared when the SCSR is read (with FE
equal to 1) followed by a read of the SCDR.
When no stop bit is detected in the received data character, the framing error (FE) bit is set. FE is set at
the same time as the RDRF. If the byte received causes both framing and overrun errors, the processor
only recognizes the overrun error. The framing error flag inhibits further transfer of data into the SCDR
until it is cleared. The FE bit is cleared when the SCSR is read (with FE equal to 1) followed by a read of
the SCDR.
7.7 SCI Registers
Five addressable registers are associated with the SCI:
Four control and status registers:
Serial communications control register 1 (SCCR1)
Serial communications control register 2 (SCCR2)
Baud rate register (BAUD)
Serial communications status register (SCSR)
One data register:
Serial communications data register (SCDR)
The SCI registers are the same for all M68HC11 E-series devices with one exception. The SCI system
for MC68HC(7)11E20 contains an extra bit in the BAUD register that provides a greater selection of baud
prescaler rates. Refer to
7.7.5 Baud Rate
Freescale Semiconductor
Register,
Figure
7-8, and
M68HC11E Family Data Sheet, Rev. 5.1
SCI Error Detection
Figure
7-9.
109