DS2196 Dallas Semiconducotr, DS2196 Datasheet - Page 104
DS2196
Manufacturer Part Number
DS2196
Description
T1 Dual Framer LIU
Manufacturer
Dallas Semiconducotr
Datasheet
1.DS2196.pdf
(157 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DS2196LN
Manufacturer:
DALLAS
Quantity:
1 170
Company:
Part Number:
DS2196LN
Manufacturer:
TI
Quantity:
1 170
Part Number:
DS2196LN
Manufacturer:
DALLAS
Quantity:
20 000
- Current page: 104 of 157
- Download datasheet (735Kb)
Receive a HDLC Message or a BOC
1. Enable RBOC and RPS interrupts
2. Wait for interrupt to occur
3. If RBOC=1, then follow steps 5 and 6
4. If RPS=1, then follow steps 7 through 12
5. If LBD=1, a BOC is present, then read the code from the RBOC register and take action as needed
6. If BD=0, a BOC has ceased, take action as needed and then return to step 1
7. Disable RPS interrupt and enable either RPE, RNE, or RHALF interrupt
8. Read RHIR to obtain REMPTY status a. if REMPTY=0, then record OBYTE, CBYTE, and POK
9. Repeat step 8
10. Wait for interrupt, skip to step 8
11. If POK=0, then discard whole packet, if POK=1, accept the packet 12. disable RPE, RNE, or
Transmit a HDLC Message
1. Make sure HDLC controller is done sending any previous messages and is current sending flags by
2. Enable either the THALF or TNF interrupt
3. Read THIR to obtain TFULL status a. if TFULL=0, then write a byte into the FIFO and skip to next
4. Repeat step 3
5. Wait for interrupt, skip to step 3
6. Disable THALF or TNF interrupt and enable TMEND interrupt
7. Wait for an interrupt, then read TUDR status bit to make sure packet was transmitted correctly.
Transmit a BOC
1. Write 6–bit code into TBOC
2. Set SBOC bit in TBOC=1
bits and then read the FIFO a1. if CBYTE=0 then skip to step 9 a2. if CBYTE=1 then skip to step 11
b. if REMPTY=1, then skip to step 10
RHALF interrupt, enable RPS interrupt and return to step 1.
checking that the FIFO is empty by reading the TEMPTY status bit in the THIR register
step (special case occurs when the last byte is to be written, in this case set TEOM=1 before writing
the byte and then skip to step 6) b. if TFULL=1, then skip to step 5
104 of 157
Related parts for DS2196
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Ds Relays
Manufacturer:
Panasonic Corporation of North America
Datasheet:
Part Number:
Description:
Switch-Mode Battery Charger Delivers 5A
Manufacturer:
Dallas Semiconducotr
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconducotr
Datasheet:
Part Number:
Description:
7-1 Silicon Delay Line
Manufacturer:
Dallas Semiconducotr
Datasheet:
Part Number:
Description:
3-in-1 Silicon Delay Line
Manufacturer:
Dallas Semiconducotr
Datasheet:
Part Number:
Description:
3-in-1 Low Voltage Silicon Delay Line
Manufacturer:
Dallas Semiconducotr
Datasheet:
Part Number:
Description:
Nonvolatile Controller x 16 Chip
Manufacturer:
Dallas Semiconducotr
Datasheet:
Part Number:
Description:
Partitioned NV Controller
Manufacturer:
Dallas Semiconducotr
Datasheet:
Part Number:
Description:
Dual Inverting Log Gain/Attenuator
Manufacturer:
Dallas Semiconducotr
Datasheet:
Part Number:
Description:
NV Trimmer Potentiometer
Manufacturer:
Dallas Semiconducotr
Datasheet:
Part Number:
Description:
Dual Digital Potentiometer Chip
Manufacturer:
Dallas Semiconducotr
Datasheet:
Part Number:
Description:
2k x 8 3V/5V Operation Static RAM
Manufacturer:
Dallas Semiconducotr
Datasheet:
Part Number:
Description:
Ultra3 LVD SCSI Terminator
Manufacturer:
Dallas Semiconducotr
Datasheet:
Part Number:
Description:
3.3V E1/T1/J1 Line Interface
Manufacturer:
Dallas Semiconducotr
Datasheet:
Part Number:
Description:
SCSI Terminator
Manufacturer:
Dallas Semiconducotr
Datasheet: