ATMEGA324P-A15MZ Atmel, ATMEGA324P-A15MZ Datasheet - Page 29

• Manufacturer Part Number: ATMEGA324P-A15MZ
• Description: MCU AVR 32KB FLASH 15MHZ 44-VQFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA324P-A15MZ

• Package / Case: 44-VQFN Exposed Pad
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Speed: 16MHz
• Number Of I /o: 32
• Eeprom Size: 1K x 8
• Core Processor: AVR
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Program Memory Size: 32KB (32K x 8)
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Connectivity: I²C, SPI, UART/USART
• Core Size: 8-Bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Calibrated Internal
RC Oscillator
2503N–AVR–06/08
Table 7. External RC Oscillator Operating Modes
When this Oscillator is selected, start-up times are determined by the SUT fuses as shown in
Table
Table 8. Start-up Times for the External RC Oscillator Clock Selection
Note:
The Calibrated Internal RC Oscillator provides a fixed 1.0, 2.0, 4.0, or 8.0 MHz clock. All fre-
quencies are nominal values at 5V and 25°C. This clock may be selected as the system clock by
programming the CKSEL fuses as shown in
components. The CKOPT Fuse should always be unprogrammed when using this clock option.
During Reset, hardware loads the calibration byte for the 1MHz into the OSCCAL Register and
thereby automatically calibrates the RC Oscillator. At 5V, 25°C and 1.0 MHz Oscillator fre-
quency selected, this calibration gives a frequency within ± 3% of the nominal frequency. Using
calibration methods as described in application notes available at www.atmel.com/avr it is possi-
ble to achieve ± 1% accuracy at any given V
as the Chip Clock, the Watchdog Oscillator will still be used for the Watchdog Timer and for the
reset time-out. For more information on the pre-programmed calibration value, see the section
“Calibration Byte” on page
Table 9. Internal Calibrated RC Oscillator Operating Modes
Note:
SUT1..0
00
01
10
11
8.
1. This option should not be used when operating close to the maximum frequency of the device.
1. The device is shipped with this option selected.
CKSEL3..0
Start-up Time from
Power-down and
0101
0110
0111
1000
Power-save
CKSEL3..0
6 CK
18 CK
18 CK
18 CK
0001
0010
0011
0100
(1)
(1)
258.
Additional Delay
(V
from Reset
CC
4.1 ms
4.1 ms
65 ms
= 5.0V)
–
Table
CC
and Temperature. When this Oscillator is used
Frequency Range (MHz)
9. If selected, it will operate with no external
Nominal Frequency (MHz)
Recommended Usage
BOD enabled
Fast rising power
Slowly rising power
Fast rising power or BOD enabled
8.0 - 12.0
0.1 - 0.9
0.9 - 3.0
3.0 - 8.0
1.0
2.0
4.0
8.0
ATmega32(L)
29