HD64F3337YCP16 Renesas Electronics America, HD64F3337YCP16 Datasheet - Page 443

• Manufacturer Part Number: HD64F3337YCP16
• Description: IC H8 MCU FLASH 60K 84PLCC
• Manufacturer: Renesas Electronics America
• Series: H8® H8/300r

Specifications of HD64F3337YCP16

• Core Processor: H8/300
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: Host Interface, I²C, SCI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 74
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 84-PLCC
• Package: 84PLCC
• Family Name: H8
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 74
• Interface Type: HIF/I2C/SCI
• On-chip Adc: 8-chx10-bit
• On-chip Dac: 2-chx8-bit
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Hardware Protection: Suspends or disables the programming and erasing of flash memory, and
resets the flash memory control register (FLMCR) and erase block registers (EBR1 and EBR2).
Details of hardware protection are as follows.
Protection
Programing
voltage (V
protect
Reset and
standby
protect
Interrupt
protect
Notes: *1 Three modes: program-verify, erase-verify, and prewrite-verify.
19.4.9
If an interrupt occurs
FLMCR is set), the following operating states can occur.
If an interrupt is generated during programming or erasing, programming or erasing is aborted
to protect the flash memory. Since memory cell values after a forced interrupt are
indeterminate, the system will not operate correctly after such an interrut.
Program runaway may result because the vector table could not be read correctly in interrupt
exception handling during programming or erasure
*2 All blocks are erase-disabled. It is not possible to specify individual blocks.
*3 For details, see section 19.7, Flash Memory Programming and Erasing Precautions.
Interrupt Handling during Flash Memory Programming and Erasing
PP
)
Description
When 12 V is not applied to the FV
FLMCR, EBR1, and EBR2 are initialized,
disabling programming and erasing. To obtain
this protection, V
When a reset occurs (including a watchdog
timer reset) or standby mode is entered,
FLMCR, EBR1, and EBR2 are initialized,
disabling programming and erasing. Note that
RES input does not ensure a reset unless the
RES pin is held low for at least 20 ms at power-
up (to enable the oscillator to settle), or at least
ten system clock cycles (10ø) during operation.
To prevent damage to the flash memory, if
interrupt input occurs while flash memory is
being programmed or erased, programming or
erasing is aborted immediately. The settings in
FLMCR, EBR1, and EBR2 are retained. This
type of protection can be cleared only by a
reset.
*1
while flash memory is being programmed or erased (while the P or E bit of
PP
should not exceed V
PP
pin,
CC
*2
.
.
*3
Program
Disabled
Disabled
Disabled
Function
Erase
Disabled
Disabled
Disabled
*2
*2
*2
Verify
Disabled
Disabled
Enabled
*1
411