ATmega168A Atmel Corporation, ATmega168A Datasheet - Page 160

• Manufacturer Part Number: ATmega168A
• Manufacturer: Atmel Corporation

Specifications of ATmega168A

• Flash (kbytes): 16 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 23
• Ext Interrupts: 24
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

18.11 Register Description
18.11.1
8271D–AVR–05/11
TCCR2A – Timer/Counter Control Register A
• Bits 7:6 – COM2A1:0: Compare Match Output A Mode
These bits control the Output Compare pin (OC2A) behavior. If one or both of the COM2A1:0
bits are set, the OC2A output overrides the normal port functionality of the I/O pin it is connected
to. However, note that the Data Direction Register (DDR) bit corresponding to the OC2A pin
must be set in order to enable the output driver.
When OC2A is connected to the pin, the function of the COM2A1:0 bits depends on the
WGM22:0 bit setting.
are set to a normal or CTC mode (non-PWM).
Table 18-2.
Table 18-3
mode.
Table 18-3.
Note:
Bit
(0xB0)
Read/Write
Initial Value
COM2A1
COM2A1
0
0
1
1
0
0
1
1
1. A special case occurs when OCR2A equals TOP and COM2A1 is set. In this case, the Com-
pare Match is ignored, but the set or clear is done at BOTTOM. See
page 152
shows the COM2A1:0 bit functionality when the WGM21:0 bits are set to fast PWM
Compare Output Mode, non-PWM Mode
Compare Output Mode, Fast PWM Mode
COM2A1
R/W
COM2A0
COM2A0
7
0
for more details.
ATmega48A/PA/88A/PA/168A/PA/328/P
0
1
0
1
0
1
0
1
Table 18-2
COM2A0
R/W
0
6
Description
Normal port operation, OC0A disconnected.
Toggle OC2A on Compare Match
Clear OC2A on Compare Match
Set OC2A on Compare Match
Description
Normal port operation, OC2A disconnected.
WGM22 = 0: Normal Port Operation, OC0A Disconnected.
WGM22 = 1: Toggle OC2A on Compare Match.
Clear OC2A on Compare Match, set OC2A at BOTTOM,
(non-inverting mode).
Set OC2A on Compare Match, clear OC2A at BOTTOM,
(inverting mode).
shows the COM2A1:0 bit functionality when the WGM22:0 bits
COM2B1
R/W
5
0
COM2B0
R/W
4
0
R
3
0
–
(1)
R
2
–
0
WGM21
R/W
1
0
”Fast PWM Mode” on
WGM20
R/W
0
0
TCCR2A
160