ATmega168A Atmel Corporation, ATmega168A Datasheet - Page 40

• Manufacturer Part Number: ATmega168A
• Manufacturer: Atmel Corporation

Specifications of ATmega168A

• Flash (kbytes): 16 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 23
• Ext Interrupts: 24
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

10. Power Management and Sleep Modes
10.1
Table 10-1.
Notes:
8271D–AVR–05/11
Sleep Mode
Idle
ADC Noise
Reduction
Power-down
Power-save
Standby
Extended
Standby
Sleep Modes
1. Only recommended with external crystal or resonator selected as clock source.
2. If Timer/Counter2 is running in asynchronous mode.
3. For INT1 and INT0, only level interrupt.
(1)
Active Clock Domains and Wake-up Sources in the Different Sleep Modes.
Active Clock Domains
Sleep modes enable the application to shut down unused modules in the MCU, thereby saving
power. The AVR provides various sleep modes allowing the user to tailor the power consump-
tion to the application’s requirements.
When enabled, the Brown-out Detector (BOD) actively monitors the power supply voltage during
the sleep periods. To further save power, it is possible to disable the BOD in some sleep modes.
See
F i g u r e 9 - 1 o n p a g e 2 7
ATmega48A/PA/88A/PA/168A/PA/328/P, and their distribution. The figure is helpful in selecting
an appropriate sleep mode.
BOD disable ability.
Note:
To enter any of the six sleep modes, the SE bit in SMCR must be written to logic one and a
SLEEP instruction must be executed. The SM2, SM1, and SM0 bits in the SMCR Register select
which sleep mode (Idle, ADC Noise Reduction, Power-down, Power-save, Standby, or Extended
Standby) will be activated by the SLEEP instruction. See
If an enabled interrupt occurs while the MCU is in a sleep mode, the MCU wakes up. The MCU
is then halted for four cycles in addition to the start-up time, executes the interrupt routine, and
resumes execution from the instruction following SLEEP. The contents of the Register File and
SRAM are unaltered when the device wakes up from sleep. If a reset occurs during sleep mode,
the MCU wakes up and executes from the Reset Vector.
”BOD Disable(1)” on page 41
X
1. BOD disable is only available for ATmega48PA/88PA/168PA/328P.
X
X
X
X
X
X
(2)
(1)
ATmega48A/PA/88A/PA/168A/PA/328/P
Oscillators
X
X
X
X
Table 10-1
X
X
X
X
(2)
(2)
(2)
(2)
for more details.
p r e s e n t s t h e d i f f e r e n t c l o c k s y s t e m s i n t h e
shows the different sleep modes, their wake up sources
X
X
X
X
X
X
(3)
(3)
(3)
(3)
(3)
X
X
X
X
X
X
Wake-up Sources
Table 10-2 on page 45
X
X
X
X
(2)
X
X
X
X
for a summary.
X
X
X
X
X
X
X
X
X
X
X
40