ATmega168A Atmel Corporation, ATmega168A Datasheet - Page 304

• Manufacturer Part Number: ATmega168A
• Manufacturer: Atmel Corporation

Specifications of ATmega168A

• Flash (kbytes): 16 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 23
• Ext Interrupts: 24
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8271D–AVR–05/11
Table 28-13. Pin Name Mapping
Table 28-14. Pin Values Used to Enter Programming Mode
Table 28-15. XA1 and XA0 Coding
Table 28-16. Command Byte Bit Coding
Signal Name in
Programming Mode
RDY/BSY
OE
WR
BS1
XA0
XA1
PAGEL
BS2
DATA
Command Byte
XA1
0
0
1
1
1000 0000
0100 0000
0010 0000
0001 0000
0001 0001
PAGEL
XA1
XA0
BS1
Pin
XA0
0
1
0
1
ATmega48A/PA/88A/PA/168A/PA/328/P
Action when XTAL1 is Pulsed
Load Flash or EEPROM Address (High or low address byte determined by BS1).
Load Data (High or Low data byte for Flash determined by BS1).
Load Command
No Action, Idle
Command Executed
Chip Erase
Write Fuse bits
Write Lock bits
Write Flash
Write EEPROM
{PC[1:0]: PB[5:0]}
Pin Name
Prog_enable[3]
Prog_enable[2]
Prog_enable[1]
Prog_enable[0]
PD1
PD2
PD3
PD4
PD5
PD6
PD7
PC2
Symbol
I/O
I/O
O
I
I
I
I
I
I
I
Function
0: Device is busy programming, 1: Device is
ready for new command
Output Enable (Active low)
Write Pulse (Active low)
Byte Select 1 (“0” selects Low byte, “1” selects
High byte)
XTAL Action Bit 0
XTAL Action Bit 1
Program memory and EEPROM Data Page
Load
Byte Select 2 (“0” selects Low byte, “1” selects
2’nd High byte)
Bi-directional Data bus (Output when OE is low)
Value
0
0
0
0
304