ATmega168A Atmel Corporation, ATmega168A Datasheet - Page 34

no-image

ATmega168A

Manufacturer Part Number
ATmega168A
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of ATmega168A

Flash (kbytes)
16 Kbytes
Pin Count
32
Max. Operating Frequency
20 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
23
Ext Interrupts
24
Usb Speed
No
Usb Interface
No
Spi
2
Twi (i2c)
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
1
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8 to 5.5
Operating Voltage (vcc)
1.8 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
6
Input Capture Channels
1
Pwm Channels
6
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATmega168A-AU
Manufacturer:
ATMEL
Quantity:
464
Part Number:
ATmega168A-AU
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega168A-AU
Manufacturer:
Microchip Technology
Quantity:
12 280
Part Number:
ATmega168A-AUR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega168A-AUR
Manufacturer:
Microchip Technology
Quantity:
420
Part Number:
ATmega168A-CCU
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega168A-CCU
Manufacturer:
Microchip Technology
Quantity:
309
Part Number:
ATmega168A-CCUR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega168A-CCUR
Manufacturer:
Microchip Technology
Quantity:
469
Part Number:
ATmega168A-MMH
Manufacturer:
Microchip Technology
Quantity:
2 027
Part Number:
ATmega168A-PU
Manufacturer:
ATMEL
Quantity:
1 000
Company:
Part Number:
ATmega168A-PU
Manufacturer:
ATMEL
Quantity:
4 800
9.6
8271D–AVR–05/11
Calibrated Internal RC Oscillator
Table 9-10.
Note:
By default, the Internal RC Oscillator provides an approximate 8.0MHz clock. Though voltage
and temperature dependent, this clock can be very accurately calibrated by the user. See
29-10 on page 323
See
This clock may be selected as the system clock by programming the CKSEL Fuses as shown in
Table
the pre-programmed calibration value into the OSCCAL Register and thereby automatically cali-
brates the RC Oscillator. The accuracy of this calibration is shown as Factory calibration in
29-10 on page
By changing the OSCCAL register from SW, see
page
The accuracy of this calibration is shown as User calibration in
When this Oscillator is used as the chip clock, the Watchdog Oscillator will still be used for the
Watchdog Timer and for the Reset Time-out. For more information on the pre-programmed cali-
bration value, see the section
Table 9-11.
Notes:
When this Oscillator is selected, start-up times are determined by the SUT Fuses as shown in
Table
Table 9-12.
Note:
Power Conditions
BOD enabled
Fast rising power
Slowly rising power
CKSEL3...
0100
0101
”System Clock Prescaler” on page 36
38, it is possible to get a higher calibration accuracy than by using the factory calibration.
0
9-11. If selected, it will operate with no external components. During reset, hardware loads
9-12.
(1)
1. This option should only be used if frequency stability at start-up is not important for the
1. The device is shipped with this option selected.
2. If 8MHz frequency exceeds the specification of the device (depends on V
1. If the RSTDISBL fuse is programmed, this start-up time will be increased to
2.
The device is shipped with this option selected.
application
Frequency Range
Fuse can be programmed in order to divide the internal frequency by 8.
14CK + 4.1ms to ensure programming mode can be entered.
Start-up Times for the Low-frequency Crystal Oscillator Clock Selection
Internal Calibrated RC Oscillator Operating Modes
Start-up times for the internal calibrated RC Oscillator clock selection
323.
for more details. The device is shipped with the CKDIV8 Fuse programmed.
7.3 - 8.1
Power-down and Power-save
ATmega48A/PA/88A/PA/168A/PA/328/P
Start-up Time from
(2)
Start-up Time from Power-
”Calibration Byte” on page
32K CK
(MHz)
1K CK
down and Power-save
Reserved
6 CK
6 CK
6 CK
for more details.
”OSCCAL – Oscillator Calibration Register” on
Recommended Usage
Stable frequency at start-up
302.
Additional Delay from
Reset (V
Table 29-10 on page
14CK + 65ms
14CK + 4.1ms
CKSEL3...0
14CK
0010
CC
(1)
(1)
= 5.0V)
(2)
CC
), the CKDIV8
323.
SUT1...0
00
01
10
11
Table
Table
34

Related parts for ATmega168A