EA-IF-E2

Manufacturer Part NumberEA-IF-E2
DescriptionINTERFACE ETHERNET (EA-PSI/BCI800R)
ManufacturerEA ELEKTRO-AUTOMATIK
EA-IF-E2 datasheet
 


Specifications of EA-IF-E2

SvhcNo SVHC (18-Jun-2010)Accessory TypeInterface Card
ApplicationsEngineering Laboratory And Complex Industrial ApplicationApproval BodiesCE / EN
Rohs CompliantYesFor Use WithEA Elektro-Automatik PSU
Lead Free Status / RoHS StatusLead free / RoHS Compliant  
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
Page 61
62
Page 62
63
Page 63
64
Page 64
65
Page 65
66
Page 66
67
Page 67
68
Page 68
69
Page 69
70
Page 70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
Page 69/102

Download datasheet (2Mb)Embed
PrevNext
About the interface cards
Commands to control the output/input
Activates/deactivates the power output/input. A logical assignment for OUTP resp. INP is used. It means, that using INP
with a power supply, which has an OUTPut, will be ignored. An electronic load will react the same way, but vice versa.
OUTPut[:STATe]?
-><B0>
OUTPut[:STATe]
<B0>
INPut[:STATe]?
->B0
INPut[:STATe]
<B0>
Examples:
OUTPON
Switches the power output on, but does not reset alarms or warnings and also does not
quit them. It means, if an alarm is persistent the command can‘t be executed.
INP1
Ditto, but for the input (of an electronic load)
Measurement commands
Used to read the latest measured results. You are required to pay attention to the averaging settings (see „Averaging“) when
using the measurement commands.
MEASure
[:SCALar]
:VOLTage[:DC]?
-><NRf>Unit
:CURRent[:DC]?
-><NRf>Unit
:POWer[:DC]?
-><NRf>Unit
:[ARRay]?
-><NRf>Unit, <NRf>Unit … Query: Actual voltage value, Actual current value, Actual power value..
Examples:
MEAS:CURR?
Measures the actual current resp. returns its average value.
MEAS:ARR?
Returns a device depending number of actual values. For PSI/EL: U, I, P
Set value commands
Set values can also be read back by attaching a question mark to the command. For the meaning of A, B and A/B mode at
the electronic loads please also read the user manual of those devices!
I. Voltage set value/ Overvoltage threshold
(Specification according to „1999 SCPI Command reference“:19 Source Subsystem)
For electronic loads applies:
• Specific commands only for electronic loads are supported since firmware 3.01 and up.
• the HIGH set value always has to be greater than the LOW set value, else an error is generated. The commands HIGH
and LOW are only valid for Level A/B operation and will generate an error in different level control modes.
• Query and setting of set values are always dedicated to the currently selected „Level Control“ and the preselected „Mode“.
That is, if Level A is active, the set value sent with VOLT is set for Level A etc., but only if mode CV is preselected. Else the
set value is ignored and an error is generated. The control mode has to be selected before the device is set into remote
operation mode. The other set values, not belonging to the preselected mode, can not be set anymore and have to be
preset. Thus, for continuous remote control of the device, we recommend to set the option „Keep set values“ in the setup
menu to „no“, hence the set values are reset to default values when switching „Mode“.
© 009, Elektro-Automatik GmbH & Co. KG
Queries the state of the power supply output
Switches the power supply output on/off
Queries the state of the electronic load input
Switches the electronic load input on/off
Query: Actual voltage value
Query: Actual current value
Query: Actual power value
EN
69