PIC18F26K80-E/SP Microchip Technology Inc., PIC18F26K80-E/SP Datasheet - Page 146

• Manufacturer Part Number: PIC18F26K80-E/SP
• Description: 28 SPDIP .300IN TUBE, ECAN, 64KB FLASH, 4KB RAM, 16 MIPS, 12-BIT ADC, CTMU
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F26K80-E/SP

• A/d Inputs: 8-Channel, 12-Bit
• Comparators: 2
• Cpu Speed: 16 MIPS
• Eeprom Memory: 256 Bytes
• Input Output: 24
• Interface: I2C/SPI/UART/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 28-pin SPDIP
• Programmable Memory: 64K Bytes
• Ram Size: 3.6K Bytes
• Speed: 64 MHz
• Temperature Range: –40 to 125 °C
• Timers: 2-8-bit, 3-16-bit
• Voltage, Range: 1.8-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part

PIC18F66K80 FAMILY
REGISTER 8-1:
DS39977C-page 146
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
EEPGD
R/W-x
When a WRERR occurs, the EEPGD and CFGS bits are not cleared. This allows tracing of the error
condition.
EEPGD: Flash Program or Data EEPROM Memory Select bit
1 = Access Flash program memory
0 = Access data EEPROM memory
CFGS: Flash Program/Data EEPROM or Configuration Select bit
1 = Access Configuration registers
0 = Access Flash program or data EEPROM memory
Unimplemented: Read as ‘ 0 ’
FREE: Flash Row Erase Enable bit
1 = Erase the program memory row addressed by TBLPTR on the next WR command (cleared by
0 = Perform write only
WRERR: Flash Program/Data EEPROM Error Flag bit
1 = A write operation is prematurely terminated (any Reset during self-timed programming in normal
0 = The write operation completed
WREN: Flash Program/Data EEPROM Write Enable bit
1 = Allows write cycles to Flash program/data EEPROM
0 = Inhibits write cycles to Flash program/data EEPROM
WR: Write Control bit
1 = Initiates a data EEPROM erase/write cycle, or a program memory erase cycle or write cycle.
0 = Write cycle to the EEPROM is complete
RD: Read Control bit
1 = Initiates an EEPROM read
0 = Does not initiate an EEPROM read
R/W-x
CFGS
completion of erase operation)
operation or an improper write attempt)
(The operation is self-timed and the bit is cleared by hardware once the write is complete.
The WR bit can only be set (not cleared) in software.)
(Read takes one cycle. RD is cleared in hardware. The RD bit can only be set (not cleared) in
software. RD bit cannot be set when EEPGD = 1 or CFGS = 1 .)
EECON1: DATA EEPROM CONTROL REGISTER 1
S = Settable bit
W = Writable bit
‘1’ = Bit is set
U-0
—
R/W-0
FREE
Preliminary
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
WRERR
R/W-x
(1)
(1)
WREN
R/W-0
 2011 Microchip Technology Inc.
x = Bit is unknown
R/S-0
WR
R/S-0
RD
bit 0