M30624FGAFP#U3 Renesas Electronics America, M30624FGAFP#U3 Datasheet - Page 11

• Manufacturer Part Number: M30624FGAFP#U3
• Description: IC M16C MCU FLASH 100QFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/60r

Specifications of M30624FGAFP#U3

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: DMA, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 20K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b, D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-QFP
• For Use With: 867-1000 - KIT QUICK START RENESAS 62PM3062PT3-CPE-3 - EMULATOR COMPACT M16C/62P/30P
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Pin Description
8
Pin Description
A
X
AV
V
A
V
CNV
RESET
X
BYTE
AV
P0
D
P1
D
P2
A
A
A
A
P3
A
P4
16
CC
IN
REF
0
0
1
8
OUT
0
8
0
8
Pin name
A
/D
/D
/D
CS
0
0
0
0
0
CC
to A
SS
to A
to A
to D
to D
9
to A
, V
to P0
to P1
to P2
to P3
to P4
0
0
SS
7
to A
0
,
A
to
SS
15
7
7
7
to CS
15
7
19
/D
/D
15
7
7
7
7
7
,
6
7
3
Reset input
Reference
voltage input
Power supply
input
CNV
Clock input
Clock output
External data
bus width
select input
Analog power
supply input
Analog power
supply input
I/O port P0
I/O port P1
I/O port P2
I/O port P3
I/O port P4
Signal name
SS
Input
Input
Input
Output
Input
Input
Output
Output
Output
Output
Output
Output
Input/output
Input/output
Input/output
Input/output
Input/output
Input/output
Input/output
Input/output
Input/output
Input/output
I/O type
Supply 2.7V to 5.5 V to the V
These pins are provided for the main clock generating circuit.Connect
a ceramic resonator or crystal between the X
use an externally derived clock, input it to the X
X
This pin is a power supply input for the A-D converter. Connect this
pin to V
This pin is a power supply input for the A-D converter. Connect this
pin to V
This is an 8-bit CMOS I/O port. It has an input/output port direction
register that allows the user to set each pin for input or output
individually. When used for input in single-chip mode, the port can be
set to have or not have a pull-up resistor in units of four bits by
software. In memory expansion and microprocessor modes, selection
of the internal pull-resistor is not available.
When set as a separate bus, these pins input and output data (D
This is an 8-bit I/O port equivalent to P0. P1
external interrupt pins as selected by software.
This is an 8-bit I/O port equivalent to P0.
These pins output 8 low-order address bits (A
If the external bus is set as an 8-bit wide multiplexed bus, these pins
input and output data (D
(A
If the external bus is set as a 16-bit wide multiplexed bus, these pins
input and output data (D
in time by multiplexing. They also output address (A
This is an 8-bit I/O port equivalent to P0.
If the external bus is set as a 16-bit wide multiplexed bus, these pins
input and output data (D
by multiplexing. They also output address (A
This is an 8-bit I/O port equivalent to P0.
This pin switches between processor modes. Connect this pin to the
V
mode (memory expansion mode) or the V
operation in microprocessor mode.
A “L” on this input resets the microcomputer.
This pin selects the width of an external data bus. A 16-bit width is
selected when this input is “L”; an 8-bit width is selected when this
input is “H”. This input must be fixed to either “H” or “L”. Connect this
pin to the V
This pin is a reference voltage input for the A-D converter.
When set as a separate bus, these pins input and output data
These pins output 8 middle-order address bits (A
These pins output A
order address bits. CS
access space.
OUT
SS
0
–A
pin when after a reset you want to start operation in single-chip
pin open.
7
) separated in time by multiplexing.
CC
SS
.
.
SS
pin when not using external data bus.
16
–A
0
–CS
0
0
7
19
–D
–D
) and output address (A
and CS
7
6
3
CC
) and output 8 low-order address bits
) and output address (A
are chip select signals used to specify an
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Function
pin. Supply 0 V to the V
0
–CS
3
CC
signals. A
5
IN
pin when starting
9
0
to P1
–A
–A
and the X
IN
8
15
8
7
M16C / 62A Group
pin and leave the
) separated in time
).
–A
).
Mitsubishi microcomputers
7
0
1
16
also function as
15
).
–A
–A
).
7
SS
OUT
) separated
19
pin.
are 4 high-
pins. To
(D
0
8
–D
–D
15
7
).
).