M30624FGAFP#U3 Renesas Electronics America, M30624FGAFP#U3 Datasheet - Page 273

• Manufacturer Part Number: M30624FGAFP#U3
• Description: IC M16C MCU FLASH 100QFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/60r

Specifications of M30624FGAFP#U3

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: DMA, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 20K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b, D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-QFP
• For Use With: 867-1000 - KIT QUICK START RENESAS 62PM3062PT3-CPE-3 - EMULATOR COMPACT M16C/62P/30P
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

270
Revision History
REV.A1
REV. A2
Version
REV. B
Revision history
Page 145 Note 2
Page 115, 139, Bit 3 of the UART2 special mode register 2 (bit symbol)
Page 43, Figure 1.10.6
Page 144, Figure 1.16.32, bit 5 of the SI/Oi control register (i=3, 4)
Page 144, Figure 1.16.32, Note 2
Page 2 Note is added in Figure 1.1.1.
Page 3 Note is added in Figure 1.1.2.
Page 10 Explanation of “Memory” is partly revised.
Page 10 Figure 1.3.1 is partly revised.
Page 22 Figure 1.7.1 is partly revised.
Page 23 Figure 1.7.2 is partly revised.
Page 23 “Internal Reserved Area Expansion Bit (PM13)” is added.
Page 24 Figure 1.7.3 is partly revised.
Page 25 Explanation of “(3) Selecting separate/multiplex bus” is partly revised.
Page 28 Explanation of “(2) Chip select signal” is partly added.
Page 29 Figure 1.9.2 is added.
Page 37 Explanation of “(2) Sub-clock” is partly revised.
Page 38 Figure 1.10.4 is partly revised.
Page 39 Explanation of “Stop Mode” is partly revised.
Page 39 Table 1.10.2 is partly revised.
Page 40 Explanation of “Wait Mode” is partly revised.
Page 40 Table 1.10.3 is partly revised.
Page 42 Explanation of “Power Control” is partly revised.
Page 62 Explanation of “Address Match Interruptl” is partly revised.
• Before data can be written to the SI/Oi transmit/receive register (addresses
0360
the SI/Oi Control Register (addresses 0362
set bit), make sure the CLKi pin input is held low. ---> • Before data can be written
to the SI/Oi transmit/receive register (addresses 0360
input must be in the high state. Also, before rewriting the SI/Oi Control Register
(addresses 0362
pin input is held high.
ASL --> ALS
Note: Writing a value to an address after “1” is written to this bit returns the bit to
Transfer direction lect bit --->Transfer direction select bit
When using the port as an input/output port by setting the SI/Oi port select bit (i =
3, 4) to “1”, be sure to set the sync clock select bit to “1”.
--->
When using the port as an input/output port by setting the SI/Oi port select bit (i =
3, 4) to “0”, be sure to set the sync clock select bit to “1”.
16
“0” . Other bits do not automatically return to “0” and they must therefore
be reset by the program.
, 0364
16
), the CLKi pin input must be in the low state. Also, before rewriting
16
, 0366
16
M16C/62A Group data sheet
)’s bit 7 (S
Contents for change
OUTi
initial value set bit), make sure the CLKi
16
, 0366
16
)’s bit 7 (S
16
, 0364
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
16
OUTi
), the CLKi pin
initial value
M16C / 62A Group
Mitsubishi microcomputers
Revision
01.3.27
99.12.21
00.7.10
00.7.3
date