M30624FGAFP#U3 Renesas Electronics America, M30624FGAFP#U3 Datasheet - Page 40

• Manufacturer Part Number: M30624FGAFP#U3
• Description: IC M16C MCU FLASH 100QFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/60r

Specifications of M30624FGAFP#U3

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: DMA, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 20K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b, D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-QFP
• For Use With: 867-1000 - KIT QUICK START RENESAS 62PM3062PT3-CPE-3 - EMULATOR COMPACT M16C/62P/30P
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Clock Generating Circuit
The following paragraphs describes the clocks generated by the clock generating circuit.
(1) Main clock
(2) Sub-clock
(3) BCLK
(4) Peripheral function clock(f
(5) f
(6) f
The main clock is generated by the main clock oscillation circuit. After a reset, the clock is divided by 8 to
the BCLK. The clock can be stopped using the main clock stop bit (bit 5 at address 0006
clock, after switching the operating clock source of CPU to the sub-clock, reduces the power dissipation.
After the oscillation of the main clock oscillation circuit has stabilized, the drive capacity of the main clock
oscillation circuit can be reduced using the X
Reducing the drive capacity of the main clock oscillation circuit reduces the power dissipation. This bit
changes to “1” when shifting from high-speed/medium-speed mode to stop mode and at a reset. When
shifting from low-speed/low power dissipation mode to stop mode, the value before stop mode is re-
tained.
The sub-clock is generated by the sub-clock oscillation circuit. No sub-clock is generated after a reset.
After oscillation is started using the port X
selected as the BCLK by using the system clock select bit (bit 7 at address 0006
that the sub-clock oscillation has fully stabilized before switching.
After the oscillation of the sub-clock oscillation circuit has stabilized, the drive capacity of the sub-clock
oscillation circuit can be reduced using the X
Reducing the drive capacity of the sub-clock oscillation circuit reduces the power dissipation. This bit
changes to “1” when shifting to stop mode and at a reset.
When the X
The BCLK is the clock that drives the CPU, and is f
1, 2, 4, 8, or 16. The BCLK is derived by dividing the main clock by 8 after a reset. The BCLK signal can
be output from BCLK pin by the BCLK output disable bit (bit 7 at address 0004
sion and the microprocessor modes.
The main clock division select bit 0(bit 6 at address 0006
speed/medium-speed to stop mode and at reset. When shifting from low-speed/low power dissipation
mode to stop mode, the value before stop mode is retained.
The clock for the peripheral devices is derived from the main clock or by dividing it by 1, 8, or 32. The
peripheral function clock is stopped by stopping the main clock or by setting the WAIT peripheral function
clock stop bit (bit 2 at 0006
This clock is derived by dividing the sub-clock by 32. It is used for the timer A and timer B counts.
This clock has the same frequency as the sub-clock. It is used for the BCLK and for the watchdog timer.
C32
C
CIN
/X
COUT
is used, set ports P8
16
) to “1” and then executing a WAIT instruction.
1
, f
8
, f
C
6
32
CIN
and P8
IN
select bit (bit 4 at address 0006
, f
-X
-X
1SIO2
OUT
COUT
C
7
or the clock is derived by dividing the main clock by
drive capacity select bit (bit 5 at address 0007
as the input ports without pull-up.
, f
drive capacity select bit (bit 3 at address 0006
8SIO2
16
) changes to “1” when shifting from high-
,f
32SIO2
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
,f
AD
)
16
16
), the sub-clock can be
) in the memory expan-
16
). However, be sure
M16C / 62A Group
Mitsubishi microcomputers
16
). Stopping the
16
16
).
).
37