M30624FGAFP#U3 Renesas Electronics America, M30624FGAFP#U3 Datasheet - Page 254

• Manufacturer Part Number: M30624FGAFP#U3
• Description: IC M16C MCU FLASH 100QFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/60r

Specifications of M30624FGAFP#U3

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: DMA, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 20K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b, D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-QFP
• For Use With: 867-1000 - KIT QUICK START RENESAS 62PM3062PT3-CPE-3 - EMULATOR COMPACT M16C/62P/30P
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Appendix Standard Serial I/O Mode 1 (Flash Memory Version)
Table 1.29.2. Status register (SRD)
Status Register (SRD)
SRD0 bits
SR7 (bit7)
SR6 (bit6)
SR5 (bit5)
SR4 (bit4)
SR3 (bit3)
SR2 (bit2)
SR1 (bit1)
SR0 (bit0)
The status register indicates operating status of the flash memory and status such as whether an erase
operation or a program ended successfully or in error. It can be read by writing the read status register
command (70
Table 1.29.2 gives the definition of each status register bit. After clearing the reset, the status register
outputs “80
Write State Machine (WSM) Status (SR7)
Erase Status (SR5)
Program Status (SR4)
Block Status After Program (SR3)
The write state machine (WSM) status indicates the operating status of the flash memory. When
power is turned on, “1” (ready) is set for it. The bit is set to “0” (busy) during an auto write or auto erase
operation, but it is set back to “1” when the operation ends.
The erase status reports the operating status of the auto erase operation. If an erase error occurs, it is
set to “1”. When the erase status is cleared, it is set to “0”.
The program status reports the operating status of the auto write operation. If a write error occurs, it is
set to “1”. When the program status is cleared, it is set to “0”.
If excessive data is written (phenomenon whereby the memory cell becomes depressed which results
in data not being read correctly), “1” is set for the block status after-program at the end of the page
write operation. In other words, when writing ends successfully, “80
“90
If “1” is written for any of the SR5, SR4 or SR3 bits, the page program, block erase, erase all unlocked
blocks and lock bit program commands are not accepted. Before executing these commands, execute
the clear status register command (50
16
” is output; and when excessive data is written, “88
16
”.
16
). Also, the status register is cleared by writing the clear status register command (50
Write state machine (WSM) status
Block status after program
Program status
Status name
Erase status
Reserved
Reserved
Reserved
Reserved
16
) and clear the status register.
Terminated in error
Terminated in error
Terminated in error
16
” is output.
Ready
"1"
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
-
-
-
-
16
” is output; when writing fails,
Definition
Terminated normally
Terminated normally
Terminated normally
M16C / 62A Group
Mitsubishi microcomputers
Busy
"0"
-
-
-
-
16
).
251