ATTINY43U-MU Atmel, ATTINY43U-MU Datasheet - Page 109

• Manufacturer Part Number: ATTINY43U-MU
• Description: MCU AVR 4K FLASH 8MHZ 20-QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY43U-MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 16
• Program Memory Size: 4KB (2K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 64 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-MLF®, QFN
• Processor Series: ATTINY4x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 4 Channel
• For Use With: ATSTK600-TINYX3U - STK600 SOCKET/ADAPTER TINYX3U
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

14.5.2
8048B–AVR–03/09
USISR – USI Status Register
Table 14-2
source used for the USI Data Register and the 4-bit counter.
Table 14-2.
• Bit 1 – USICLK: Clock Strobe
Writing a one to this bit location strobes the USI Data Register to shift one step and the counter
to increment by one, provided that the software clock strobe option has been selected by writing
USICS1:0 bits to zero. The output will change immediately when the clock strobe is executed,
i.e., during the same instruction cycle. The value shifted into the USI Data Register is sampled
the previous instruction cycle.
When an external clock source is selected (USICS1 = 1), the USICLK function is changed from
a clock strobe to a Clock Select Register. Setting the USICLK bit in this case will select the
USITC strobe bit as clock source for the 4-bit counter (see
The bit will be read as zero.
• Bit 0 – USITC: Toggle Clock Port Pin
Writing a one to this bit location toggles the USCK/SCL value either from 0 to 1, or from 1 to 0.
The toggling is independent of the setting in the Data Direction Register, but if the PORT value is
to be shown on the pin the corresponding DDR pin must be set as output (to one). This feature
allows easy clock generation when implementing master devices.
When an external clock source is selected (USICS1 = 1) and the USICLK bit is set to one, writ-
ing to the USITC strobe bit will directly clock the 4-bit counter. This allows an early detection of
when the transfer is done when operating as a master device.
The bit will read as zero.
The Status Register contains interrupt flags, line status flags and the counter value.
• Bit 7 – USISIF: Start Condition Interrupt Flag
When two-wire mode is selected, the USISIF Flag is set (to one) when a start condition has
been detected. When three-wire mode or output disable mode has been selected any edge on
the SCK pin will set the flag.
Bit
0x0E (0x2E)
Read/Write
Initial Value
USICS1
0
0
0
1
1
1
1
USICS0
shows the relationship between the USICS[1:0] and USICLK setting and clock
USISIF
Relationship between the USICS1:0 and USICLK Setting
0
0
1
0
1
0
1
R/W
7
0
USICLK
USIOIF
R/W
X
6
0
0
1
0
0
1
1
Clock Source
No Clock
Software clock strobe (USICLK)
Timer/Counter0 Compare Match
External, positive edge
External, negative edge
External, positive edge
External, negative edge
USIPF
R/W
5
0
USIDC
R
4
0
USICNT3
R/W
3
0
Table
USICNT2
R/W
2
0
4-bit Counter Clock Source
No Clock
Software clock strobe (USICLK)
Timer/Counter0 Compare Match
External, both edges
External, both edges
Software clock strobe (USITC)
Software clock strobe (USITC)
14-2).
USICNT1
R/W
1
0
USICNT0
R/W
0
0
USISR
109