ATTINY43U-MU Atmel, ATTINY43U-MU Datasheet - Page 144

• Manufacturer Part Number: ATTINY43U-MU
• Description: MCU AVR 4K FLASH 8MHZ 20-QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY43U-MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 16
• Program Memory Size: 4KB (2K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 64 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-MLF®, QFN
• Processor Series: ATTINY4x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 4 Channel
• For Use With: ATSTK600-TINYX3U - STK600 SOCKET/ADAPTER TINYX3U
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

19.6
19.6.1
19.6.2
144
Parallel Programming
ATtiny43U
Enter Programming Mode
Considerations for Efficient Programming
The XA1/XA0 pins determine the action executed when the CLKI pin is given a positive pulse.
The bit coding is shown in
Table 19-12. XA1 and XA0 Coding
When pulsing WR or OE, the command loaded determines the action executed. The different
Commands are shown in
Table 19-13. Command Byte Bit Coding
The following algorithm puts the device in parallel programming mode:
The loaded command and address are retained in the device during programming. For efficient
programming, the following should be considered.
Command Byte
1. Apply 4.5 - 5.5V between V
2. Set RESET to “0” and toggle CLKI at least six times.
3. Set the Prog_enable pins listed in
4. Apply 11.5 - 12.5V to RESET. Any activity on Prog_enable pins within 100 ns after
5. Wait at least 50 µs before sending a new command.
XA1
0
0
1
1
100 ns.
+12V has been applied to RESET, will cause the device to fail entering programming
mode.
1000 0000
0100 0000
0010 0000
0001 0000
0001 0001
0000 1000
0000 0100
0000 0010
0000 0011
XA0
0
1
0
1
Action when CLKI is Pulsed
Load Flash or EEPROM Address (High or low address byte determined by BS1).
Load Data (High or Low data byte for Flash determined by BS1).
Load Command
No Action, Idle
Table
Table
Command Executed
Chip Erase
Write Fuse bits
Write Lock bits
Write Flash
Write EEPROM
Read Signature Bytes and Calibration byte
Read Fuse and Lock bits
Read Flash
Read EEPROM
19-13.
19-12.
CC
and GND.
Table 19-11 on page 143
to “0000” and wait at least
8048B–AVR–03/09