PIC24FJ256DA206-I/MR Microchip Technology, PIC24FJ256DA206-I/MR Datasheet - Page 242

• Manufacturer Part Number: PIC24FJ256DA206-I/MR
• Description: MCU PIC 16BIT FLASH 256K 64VQFN
• Manufacturer: Microchip Technology
• Series: PIC® 24Fr

Specifications of PIC24FJ256DA206-I/MR

• Program Memory Type: FLASH
• Program Memory Size: 256KB (85.5K x 24)
• Package / Case: 64-VFQFN, Exposed Pad
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: I²C, IrDA, SPI, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, GFX, LVD, POR, PWM, WDT
• Number Of I /o: 52
• Ram Size: 96K x 8
• Voltage - Supply (vcc/vdd): 2.2 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC24FJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 96 KB
• Interface Type: UART, SPI, USB, I2C, RS-485, RS-232
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 5
• Operating Supply Voltage: 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, AC164127-4, AC164127-6, AC164139, DM240001, DM240312, DV164039
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC24FJ256DA210 FAMILY
18.1.2
18.1.2.1
PIC24FJ256DA210 family devices have a built-in
15 k pull-down resistor on the D+ and D- lines. These
are used in tandem to signal to the bus that the micro-
controller is operating in Host mode. They are engaged
by setting the HOSTEN bit (U1CON<3>). If the OTGEN
bit (U1OTGCON<2>) is set, then these pull-downs are
enabled by setting the DPPULDWN and DMPULDWN
bits (U1OTGCON<5:4>).
18.1.2.2
In Host mode, as well as Host mode in On-The-Go
operation, the USB 2.0 Specification requires that the
host application should supply power on V
FIGURE 18-6:
FIGURE 18-7:
DS39969B-page 242
HOST AND OTG MODES
D+ and D- Pull-Down Resistors
Power Configurations
Connector
Micro A/B
Connector
Micro A/B
V
GND
BUS
D+
HOST INTERFACE EXAMPLE
OTG INTERFACE EXAMPLE
D-
V
ID
GND
BUS
D+
D-
ID
4.7 µF
150 µF
1 µF
40 k
BUS
Thermal Fuse
Polymer PTC
. Since
2 k
2 k
GND
C+
C-
V
OUT
MCP1253
SELECT
PGOOD
SHND
+5V
0.1 µF,
3.3V
V
IN
the microcontroller is running below V
able to source sufficient current, a separate power
supply must be provided.
When the application is always operating in Host mode,
a simple circuit can be used to supply V
late current on the bus (Figure 18-6). For OTG opera-
tion, it is necessary to be able to turn V
needed, as the microcontroller switches between
Device and Host modes. A typical example using an
external charge pump is shown in Figure 18-7.
+3.3V +3.3V
V
DD
10 µF
V
V
A/D Pin
V
D+
D-
ID
V
USB
PIC
DD
BUS
SS
I/O
I/O
V
D+
D-
ID
V
PIC
BUS
SS
®
MCU
®
MCU
 2010 Microchip Technology Inc.
BUS
BUS
BUS
, and is not
on or off as
and regu-