HD64F2636UF20 Renesas Electronics America, HD64F2636UF20 Datasheet - Page 648

• Manufacturer Part Number: HD64F2636UF20
• Description: IC H8S MCU FLASH 128K 128QFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8S/2600r

Specifications of HD64F2636UF20

• Core Processor: H8S/2600
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: CAN, SCI, SmartCard
• Peripherals: Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 72
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 12x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 128-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Section 15 I
(Only for the H8S/2638, H8S/2639, and H8S/2630)
The following items are not initialized:
• Actual register values (ICDR, SAR, SARX, ICMR, ICCR, ICSR, DDCSWR, and STCR)
• Internal latches used to retain register read information for setting/clearing flags in the ICMR,
• The value of the ICMR register bit counter (BC2 to BC0)
• Generated interrupt sources (interrupt sources transferred to the interrupt controller)
Notes on Initialization:
• Interrupt flags and interrupt sources are not cleared, and so flag clearing measures must be
• Basically, other register flags are not cleared either, and so flag clearing measures must be
• When initialization is performed by means of the DDCSWR register, the write data for bits
• If a flag clearing setting is made during transmission/reception, the IIC module will stop
The value of the BBSY bit cannot be modified directly by this module clear function, but since the
stop condition pin waveform is generated according to the state and release timing of the SCL and
SDA pins, the BBSY bit may be cleared as a result. Similarly, state switching of other bits and
flags may also have an effect.
To prevent problems caused by these factors, the following procedure should be used when
initializing the IIC state.
1. Execute initialization of the internal state according to the setting of bits CLR3 to CLR0, or
2. Execute a stop condition issuance instruction (write 0 to BBSY and SCP) to clear the BBST bit
3. Re-execute initialization of the internal state according to the setting of bits CLR3 to CLR0, or
4. Initialize (re-set) the IIC registers.
Page 598 of 1458
ICCR, ICSR, and DDCSWR registers
taken as necessary.
taken as necessary.
CLR3 to CLR0 is not retained. To perform IIC clearance, bits CLR3 to CLR0 must be written
to simultaneously using an MOV instruction. Do not use a bit manipulation instruction such as
BCLR. Similarly, when clearing is required again, all the bits must be written to
simultaneously in accordance with the setting.
transmitting/receiving at that point and the SCL and SDA pins will be released. When
transmission/reception is started again, register initialization, etc., must be carried out as
necessary to enable correct communication as a system.
according to the ICE bit.
to 0, and wait for two transfer rate clock cycles.
according to the ICE bit.
2
C Bus Interface [Option]
H8S/2639, H8S/2638, H8S/2636,
REJ09B0103-0800 Rev. 8.00
H8S/2630, H8S/2635 Group
May 28, 2010