73S1210F-68IM/F Maxim Integrated Products, 73S1210F-68IM/F Datasheet - Page 9

• Manufacturer Part Number: 73S1210F-68IM/F
• Description: IC SMART CARD READER 68-QFN
• Manufacturer: Maxim Integrated Products

Specifications of 73S1210F-68IM/F

• Core Processor: 80515
• Core Size: 8-Bit
• Speed: 24MHz
• Connectivity: I²C, SmartCard, UART/USART
• Peripherals: LED, POR, WDT
• Number Of I /o: 8
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 6.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

DS_1210F_001
Rev. 1.4
Pin Name
PRES
CLK
RST
IO
AUX1
AUX2
VCC
GND
VPC
VBUS
VBAT
VP
LIN
ON_OFF
OFF_REQ
TBUS(3:0)
0
1
2
3
53
55
57
61
60
59
58
56
65
62
64
54
66
63
52
50
46
44
41
34
36
38
42
41
40
39
37
44
35
43
33
1
GND
PSO
PSO
PSI
PSI
PSI
PSI
IO
IO
IO
IO
O
O
O
I
I
Figure 41
Figure 39
Figure 39
Figure 40
Figure 40
Figure 40
Figure 43
Figure 33
Description
Smart Card presence. Active high. Note: the pin has a
very weak pull down resistor. In noisy environments, an
external pull down may be desired to insure against a
false card event.
Smart Card clock signal.
Smart Card reset signal.
Smart Card Data IO signal.
Auxiliary Smart Card IO signal (C4).
Auxiliary Smart Card IO signal (C8).
Smart Card VCC supply voltage output. A 0.47µF
capacitor is required and should be located at the smart
card connector. The capacitor should be a ceramic type
with low ESR.
Smart Card Ground.
Power supply source for main voltage converter circuit. A
10µF and a 0.1µF capacitor are required at the VPC input.
The 10µF capacitor should be a ceramic type with low
ESR.
Alternate power source input from external power supply.
Alternate power source input, typically from two series
cells, V > 4V.
Intermediate output of main converter circuit. Requires an
external 4.7µF low ESR filter capacitor to GND.
Connection to 10µH inductor for internal step up
converter. Note: inductor must be rated for 400 mA
maximum peak current.
Power control pin. Connected to normally open SPST
switch to ground. Closing switch for duration greater than
debounce period will turn 73S1210F on. If 73S1210F is
on, closing switch will flag the 73S1210F to go to the off
state. Firmware will control when the power is shut down.
Digital output. If ON_OFF switch is closed (to ground) for
debounce duration and circuit is “on,” OFF_REQ will go
high (Request to turn OFF). This output should be
connected to an interrupt pin to signal the CPU core that a
request to shut down power has been initiated. The
firmware can then perform all of its shut down
housekeeping duties before shutting down V
Trace bus signals for ICE.
73S1210F Data Sheet
DD
.
9