LPC1769FBD100,551 NXP Semiconductors, LPC1769FBD100,551 Datasheet - Page 462

• Manufacturer Part Number: LPC1769FBD100,551
• Description: IC ARM CORTEX MCU 512K 100-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC17xxr

Specifications of LPC1769FBD100,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 100-LQFP
• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 120MHz
• Connectivity: CAN, Ethernet, I²C, IrDA, Microwire, SPI, SSI, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 70
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 3.6 V
• Data Converters: A/D 8x12b, D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC17
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: Ethernet, USB, OTG, CAN
• Maximum Clock Frequency: 120 MHz
• Number Of Programmable I/os: 70
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, MCB1760, MCB1760U, MCB1760UME
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 8 Channel
• On-chip Dac: 10 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4966; 935290522551

NXP Semiconductors
Table 402. Miscellaneous States
UM10360
User manual
Status
Code
(I2CSTAT)
0xF8
0x00
19.9.6.1 I2STAT = 0xF8
19.9.6.2 I2STAT = 0x00
Status of the I
and hardware
No relevant state
information available;
SI = 0.
Bus error during MST
or selected slave
modes, due to an
illegal START or
STOP condition. State
0x00 can also occur
when interference
causes the I
to enter an undefined
state.
19.9.7.1 Simultaneous repeated START conditions from two masters
19.9.6 Miscellaneous states
19.9.7 Some special cases
2
There are two I2STAT codes that do not correspond to a defined I
Table
This status code indicates that no relevant information is available because the serial
interrupt flag, SI, is not yet set. This occurs between other states and when the I
is not involved in a serial transfer.
This status code indicates that a bus error has occurred during an I
bus error is caused when a START or STOP condition occurs at an illegal position in the
format frame. Examples of such illegal positions are during the serial transfer of an
address byte, a data byte, or an acknowledge bit. A bus error may also be caused when
external interference disturbs the internal I
set. To recover from a bus error, the STO flag must be set and SI must be cleared. This
causes the I
clear the STO flag (no other bits in I2CON are affected). The SDA and SCL lines are
released (a STOP condition is not transmitted).
The I
during a serial transfer:
A repeated START condition may be generated in the master transmitter or master
receiver modes. A special case occurs if another master simultaneously generates a
repeated START condition (see
either master since they were both transmitting the same data.
C block
2
C-bus
2
402). These are discussed below.
C hardware has facilities to handle the following special cases that may occur
Application software response
To/From I2DAT
No I2DAT action
No I2DAT action
2
C block to enter the “not addressed” slave mode (a defined state) and to
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 19 August 2010
To I2CON
STA STO SI
0
No I2CON action
Figure
1
97). Until this occurs, arbitration is not lost by
0
2
C block signals. When a bus error occurs, SI is
AA
X
Next action taken by I
Wait or proceed current transfer.
Only the internal hardware is affected in
the MST or addressed SLV modes. In all
cases, the bus is released and the I
block is switched to the not addressed
SLV mode. STO is reset.
Chapter 19: LPC17xx I2C0/1/2
2
C hardware state (see
2
C serial transfer. A
UM10360
© NXP B.V. 2010. All rights reserved.
2
C hardware
2
462 of 840
C block
2
C