LPC2458FET180,551 NXP Semiconductors, LPC2458FET180,551 Datasheet - Page 364

• Manufacturer Part Number: LPC2458FET180,551
• Description: IC ARM7 MCU FLASH 512K 180TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2458FET180,551

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 136
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 180-TFBGA
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN, Ethernet, I2C, I2S, IrDA, SPI, SSP, UART, USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 136
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, SAB-TFBGA180
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• On-chip Dac: 10 bit, 1 Channel
• Package: 180TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• For Use With: 622-1023 - BOARD SCKT ADAPTER FOR TFBGA180622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 568-4258; 935282454551; LPC2458FET180-S

NXP Semiconductors
Table 347. SIE command code table
Table 348. Device Set Address Register bit description
UM10237_4
User manual
Command name
Device commands
Set Address
Configure Device
Set Mode
Read Current Frame Number
Read Test Register
Set Device Status
Get Device Status
Get Error Code
Read Error Status
Endpoint Commands
Select Endpoint
Select Endpoint/Clear Interrupt
Set Endpoint Status
Clear Buffer
Validate Buffer
Bit
6:0
7
Symbol
DEV_ADDR
DEV_EN
11.1 Set Address (Command: 0xD0, Data: write 1 byte)
11.2 Configure Device (Command: 0xD8, Data: write 1 byte)
The Set Address command is used to set the USB assigned address and enable the
(embedded) function. The address set in the device will take effect after the status stage
of the control transaction. After a bus reset, DEV_ADDR is set to 0x00, and DEV_EN is
set to 1. The device will respond to packets for function address 0x00, endpoint 0 (default
endpoint).
A value of 1 written to the register indicates that the device is configured and all the
enabled non-control endpoints will respond. Control endpoints are always enabled and
respond even if the device is not configured, in the default state.
Description
Device address set by the software. After a bus reset this field is set to
0x00.
Device Enable. After a bus reset this bit is set to 1.
0: Device will not respond to any packets.
1: Device will respond to packets for function address DEV_ADDR.
Recipient
Device
Device
Device
Device
Device
Device
Device
Device
Device
Endpoint 0
Endpoint 1
Endpoint xx
Endpoint 0
Endpoint 1
Endpoint xx
Endpoint 0
Endpoint 1
Endpoint xx
Selected Endpoint
Selected Endpoint
Rev. 04 — 26 August 2009
Code (Hex)
41
D0
D8
F3
F5
FD
FE
FE
FF
FB
00
01
xx
40
xx + 40
40
41
xx + 40
F2
FA
Chapter 13: LPC24XX USB device controller
Data phase
Write 1 byte
Write 1 byte
Write 1 byte
Read 1 or 2 bytes
Read 2 bytes
Write 1 byte
Read 1 byte
Read 1 byte
Read 1 byte
Read 1 byte (optional)
Read 1 byte (optional)
Read 1 byte (optional)
Read 1 byte
Read 1 byte
Read 1 byte
Write 1 byte
Write 1 byte
Write 1 byte
Read 1 byte (optional)
None
UM10237
© NXP B.V. 2009. All rights reserved.
Reset value
0x00
0
364 of 792