LPC2458FET180,551 NXP Semiconductors, LPC2458FET180,551 Datasheet - Page 560

• Manufacturer Part Number: LPC2458FET180,551
• Description: IC ARM7 MCU FLASH 512K 180TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2458FET180,551

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 136
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 180-TFBGA
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN, Ethernet, I2C, I2S, IrDA, SPI, SSP, UART, USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 136
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, SAB-TFBGA180
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• On-chip Dac: 10 bit, 1 Channel
• Package: 180TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• For Use With: 622-1023 - BOARD SCKT ADAPTER FOR TFBGA180622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 568-4258; 935282454551; LPC2458FET180-S

NXP Semiconductors
UM10237_4
User manual
Fig 110. Pending command start
MCIDAT0
CmdPend
cmd state
MCICMD
MCICLK
counter
data
5.3.10 CRC Token status
5.3.9 Bus mode
Z
3
The data block counter determines the end of a data block. If the counter is zero, the
end-of-data condition is TRUE (see
0xE008 C02C)”
In wide bus mode, all four data signals (MCIDAT[3:0]) are used to transfer data, and the
CRC code is calculated separately for each data signal. While transmitting data blocks to
a card, only MCIDAT0 is used for the CRC token and busy signalling. The start bit must be
transmitted on all four data signals at the same time (during the same clock period). If the
start bit is not detected on all data signals on the same clock edge while receiving data,
the DPSM sets the start bit error flag and moves to the IDLE state.
The data path also operates in half-duplex mode, where data is either sent to a card or
received from a card. While not being transferred, MCIDAT[3:0] are in the HI-Z state.
Data on these signals is synchronous to the rising edge of the clock period.
If standard bus mode is selected the MCIDAT[3:1] outputs are always in HI-Z state and
only the MCIDAT0 output is driven LOW when data is transmitted.
Design note: If wide mode is selected, both nMCIDAT0EN and nMCIDATEN outputs are
driven low at the same time. If not, the MCIDAT[3:1] outputs are always in HI-Z state
(nMCIDATEN) is driven HIGH), and only the MCIDAT0 output is driven LOW when data is
transmitted.
The CRC token status follows each write data block, and determines whether a card has
received the data block correctly. When the token has been received, the card asserts a
busy signal by driving MCIDAT0 LOW.
Table 486. CRC token status
Token
010
101
2
Z
7
PEND
1
Z
for more information).
Description
Card has received error-free data block.
Card has detected a CRC error.
0
Z
Rev. 04 — 26 August 2009
7
Z
Section 21–6.9 “Data Control Register (MCIDataCtrl -
6
S
Table 21–486
Chapter 21: LPC24XX SD/MMC card interface
CMD
5
CMD
shows the CRC token status values.
4
6
SEND
CMD
3
CMD
UM10237
2
© NXP B.V. 2009. All rights reserved.
CMD
1
560 of 792