LPC2458FET180,551 NXP Semiconductors, LPC2458FET180,551 Datasheet - Page 537

• Manufacturer Part Number: LPC2458FET180,551
• Description: IC ARM7 MCU FLASH 512K 180TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2458FET180,551

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 136
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 180-TFBGA
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN, Ethernet, I2C, I2S, IrDA, SPI, SSP, UART, USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 136
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, SAB-TFBGA180
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• On-chip Dac: 10 bit, 1 Channel
• Package: 180TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• For Use With: 622-1023 - BOARD SCKT ADAPTER FOR TFBGA180622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 568-4258; 935282454551; LPC2458FET180-S

NXP Semiconductors
4. Pin descriptions
5. Bus description
UM10237_4
User manual
5.1 Texas Instruments synchronous serial frame format
Table 469. SSP pin descriptions
Figure 20–96
supported by the SSP module.
Pin
Name
SCK0/1
SSEL0/1 I/O
MISO0/1 I/O
MOSI0/1 I/O
Type
I/O
shows the 4-wire Texas Instruments synchronous serial frame format
Interface pin
name/function
SPI
SCK
SSEL FS
MISO DR(M)
MOSI DX(M)
Rev. 04 — 26 August 2009
SSI
CLK
DX(S)
DR(S)
Microwire
SK
CS
SI(M)
SO(S)
SO(M)
SI(S)
Pin Description
Serial Clock. SCK/CLK/SK is a clock signal used
to synchronize the transfer of data. It is driven by
the master and received by the slave. When SPI
interface is used the clock is programmable to be
active high or active low, otherwise it is always
active high. SCK1 only switches during a data
transfer. Any other time, the SSPn either holds it in
its inactive state, or does not drive it (leaves it in
high impedance state).
Frame Sync/Slave Select. When the SSPn is a
bus master, it drives this signal from shortly before
the start of serial data, to shortly after the end of
serial data, to signify a data transfer as appropriate
for the selected bus and mode. When the SSPn is a
bus slave, this signal qualifies the presence of data
from the Master, according to the protocol in use.
When there is just one bus master and one bus
slave, the Frame Sync or Slave Select signal from
the Master can be connected directly to the slave’s
corresponding input. When there is more than one
slave on the bus, further qualification of their Frame
Select/Slave Select inputs will typically be
necessary to prevent more than one slave from
responding to a transfer.
Master In Slave Out. The MISO signal transfers
serial data from the slave to the master. When the
SSPn is a slave, serial data is output on this signal.
When the SSPn is a master, it clocks in serial data
from this signal. When the SSPn is a slave and is
not selected by FS/SSEL, it does not drive this
signal (leaves it in high impedance state).
Master Out Slave In. The MOSI signal transfers
serial data from the master to the slave. When the
SSPn is a master, it outputs serial data on this
signal. When the SSPn is a slave, it clocks in serial
data from this signal.
Chapter 20: LPC24XX SSP interface SSP0/1
UM10237
© NXP B.V. 2009. All rights reserved.
537 of 792