LPC2458FET180,551 NXP Semiconductors, LPC2458FET180,551 Datasheet - Page 429

• Manufacturer Part Number: LPC2458FET180,551
• Description: IC ARM7 MCU FLASH 512K 180TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2458FET180,551

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 136
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 180-TFBGA
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN, Ethernet, I2C, I2S, IrDA, SPI, SSP, UART, USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 136
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, SAB-TFBGA180
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• On-chip Dac: 10 bit, 1 Channel
• Package: 180TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• For Use With: 622-1023 - BOARD SCKT ADAPTER FOR TFBGA180622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 568-4258; 935282454551; LPC2458FET180-S

NXP Semiconductors
UM10237_4
User manual
4.5 UARTn Interrupt Identification Register (U0IIR - 0xE000 C008, U2IIR -
0xE007 8008, U3IIR - 0x7008 C008, Read Only)
The UnIIR provides a status code that denotes the priority and source of a pending
interrupt. The interrupts are frozen during an UnIIR access. If an interrupt occurs during
an UnIIR access, the interrupt is recorded for the next UnIIR access.
Table 383. UARTn Interrupt Identification Register (U0IIR - address 0xE000 C008,
Bit UnIIR[9:8] are set by the auto-baud function and signal a time-out or end of auto-baud
condition. The auto-baud interrupt conditions are cleared by setting the corresponding
Clear bits in the Auto-baud Control Register.
If the IntStatus bit is 1 no interrupt is pending and the IntId bits will be zero. If the IntStatus
is 0, a non auto-baud interrupt is pending in which case the IntId bits identify the type of
interrupt and handling as described in
interrupt handler routine can determine the cause of the interrupt and how to clear the
active interrupt. The UnIIR must be read in order to clear the interrupt prior to exiting the
Interrupt Service Routine.
The UARTn RLS interrupt (UnIIR[3:1] = 011) is the highest priority interrupt and is set
whenever any one of four error conditions occur on the UARTn Rx input: overrun error
(OE), parity error (PE), framing error (FE) and break interrupt (BI). The UARTn Rx error
condition that set the interrupt can be observed via U0LSR[4:1]. The interrupt is cleared
upon an UnLSR read.
Bit
0
3:1
5:4
7:6
8
9
31:10 -
Symbol
IntStatus
IntId
-
FIFO Enable
ABEOInt
ABTOInt
U2IIR - 0x7008 8008, U3IIR - 0x7008 C008, Read Only) bit description
Value Description
010
001
011
110
Rev. 04 — 26 August 2009
0
1
Interrupt status. Note that U1IIR[0] is active low. The
pending interrupt can be determined by evaluating
UnIIR[3:1].
At least one interrupt is pending.
No interrupt is pending.
Interrupt identification. UnIER[3:1] identifies an interrupt
corresponding to the UARTn Rx FIFO. All other
combinations of UnIER[3:1] not listed above are reserved
(000,100,101,111).
1 - Receive Line Status (RLS).
2a - Receive Data Available (RDA).
2b - Character Time-out Indicator (CTI).
3 - THRE Interrupt
Reserved, user software should not write ones to reserved
bits. The value read from a reserved bit is not defined.
These bits are equivalent to UnFCR[0].
End of auto-baud interrupt. True if auto-baud has finished
successfully and interrupt is enabled.
Auto-baud time-out interrupt. True if auto-baud has timed
out and interrupt is enabled.
Reserved, user software should not write ones to reserved
bits. The value read from a reserved bit is not defined.
Table
16–384. Given the status of UnIIR[3:0], an
Chapter 16: LPC24XX UART0/2/3
UM10237
© NXP B.V. 2009. All rights reserved.
429 of 792
Reset
Value
1
0
NA
0
0
0
NA