C8051F066-GQ Silicon Laboratories Inc, C8051F066-GQ Datasheet - Page 205

• Manufacturer Part Number: C8051F066-GQ
• Description: MCU 8-Bit C8051F06x 8051 CISC 32KB Flash 3.3V 100-Pin TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F06xr

Specifications of C8051F066-GQ

• Package: 100TQFP
• Device Core: 8051
• Family Name: C8051F06x
• Maximum Speed: 25 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 59
• Interface Type: I2C/SMBus/SPI/UART
• On-chip Adc: 2-chx16-bit
• Number Of Timers: 5
• Ram Size: 4.25 KB
• Program Memory Size: 32 KB
• Program Memory Type: Flash
• Operating Temperature: -40 to 85 °C
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 59
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 2x16b
• Oscillator Type: Internal
• Package / Case: 100-TQFP, 100-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 336-1221

18.1. Ports 0 through 3 and the Priority Crossbar Decoder
The Priority Crossbar Decoder, or “Crossbar”, allocates and assigns Port pins on Port 0 through Port 3 to
the digital peripherals (UARTs, SMBus, PCA, Timers, etc.) on the device using a priority order. The Port
pins are allocated in order starting with P0.0 and continue through P3.7 (on the C8051F060/2/4/6) or P2.7
(on the C8051F061/3/5/7) if necessary. The digital peripherals are assigned Port pins in a priority order
which is listed in Figure 18.3, with UART0 having the highest priority and CNVSTR2 having the lowest pri-
ority.
18.1.1. Crossbar Pin Assignment and Allocation
The Crossbar assigns Port pins to a peripheral if the corresponding enable bits of the peripheral are set to
a logic 1 in the Crossbar configuration registers XBR0, XBR1, XBR2, and XBR3, shown in Figure 18.5,
Figure 18.6, Figure 18.7, and Figure 18.8. For example, if the UART0EN bit (XBR0.2) is set to a logic 1,
the TX0 and RX0 pins will be mapped to P0.0 and P0.1 respectively. Because UART0 has the highest pri-
ority, its pins will always be mapped to P0.0 and P0.1 when UART0EN is set to a logic 1. If a digital periph-
TX0
RX0
SCK
MISO
MOSI
NSS
SDA
SCL
TX1
RX1
CEX0
CEX1
CEX2
CEX3
CEX4
CEX5
ECI
CP0
CP1
CP2
T0
/INT0
T1
/INT1
T2
T2EX
T3
T3EX
T4
T4EX
/SYSCLK
CNVSTR2
PIN I/O 0





                
                 
                  
                   
                    
                     
                      
                       
                        
                         
                          
                           
                            
                             
                              
                               





1


    
      
        

2


    
      
        

3
P0

        

4

        

5
        
6
NSS is not assigned to a port pin when the SPI is placed in 3-wire mode
        
7
0
Figure 18.3. Priority Crossbar Decode Table
1
2
(P1MDIN = 0xFF; P2MDIN = 0xFF)
3
P1
4
5
6
7
0
Rev. 1.2
1
2
C8051F060/1/2/3/4/5/6/7
3
P2
4
5
6
7
0
1
2
3
P3
4
5
6
7
Crossbar Register Bits
UART0EN:
UART1EN:
CNVSTE2: XBR3.2
SMB0EN:
PCA0ME:
SYSCKE: XBR1.7
SPI0EN:
T2EXE: XBR1.6
T3EXE: XBR3.1
T4EXE: XBR2.4
ECI0E: XBR0.6
INT0E: XBR1.2
INT1E: XBR1.4
CP0E: XBR0.7
CP1E: XBR1.0
CP2E: XBR3.3
T0E: XBR1.1
T1E: XBR1.3
T2E: XBR1.5
T3E: XBR3.0
T4E: XBR2.3
XBR0.2
XBR0.1
XBR0.0
XBR2.2
XBR0.[5:3]
205