C8051F066-GQ Silicon Laboratories Inc, C8051F066-GQ Datasheet - Page 288

• Manufacturer Part Number: C8051F066-GQ
• Description: MCU 8-Bit C8051F06x 8051 CISC 32KB Flash 3.3V 100-Pin TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F06xr

Specifications of C8051F066-GQ

• Package: 100TQFP
• Device Core: 8051
• Family Name: C8051F06x
• Maximum Speed: 25 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 59
• Interface Type: I2C/SMBus/SPI/UART
• On-chip Adc: 2-chx16-bit
• Number Of Timers: 5
• Ram Size: 4.25 KB
• Program Memory Size: 32 KB
• Program Memory Type: Flash
• Operating Temperature: -40 to 85 °C
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 59
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 2x16b
• Oscillator Type: Internal
• Package / Case: 100-TQFP, 100-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 336-1221

C8051F060/1/2/3/4/5/6/7
The C/T0 bit (TMOD.2) selects the counter/timer's clock source. When C/T0 is set to logic 1, high-to-low
transitions at the selected Timer 0 input pin (T0) increment the timer register (Refer to
“18.1. Ports 0 through 3 and the Priority Crossbar Decoder” on page 205
configuring external I/O pins). Clearing C/T selects the clock defined by the T0M bit (CKCON.3). When
T0M is set, Timer 0 is clocked by the system clock. When T0M is cleared, Timer 0 is clocked by the source
selected by the Clock Scale bits in CKCON (see Figure 24.6).
Setting the TR0 bit (TCON.4) enables the timer when either GATE0 (TMOD.3) is logic 0 or the input signal
/INT0 is logic-level 1. Setting GATE0 to ‘1’ allows the timer to be controlled by the external input signal /
INT0 (see
ments.
Setting TR0 does not force the timer to reset. The timer registers should be loaded with the desired initial
value before the timer is enabled.
TL1 and TH1 form the 13-bit register for Timer 1 in the same manner as described above for TL0 and TH0.
Timer 1 is configured and controlled using the relevant TCON and TMOD bits just as with Timer 0. The
input signal /INT1 is used with Timer 1.
288
/INT0
T0
Crossbar
Section “13.3.5. Interrupt Register Descriptions” on page
Pre-scaled Clock
SYSCLK
TR0
0
1
1
1
GATE0
X = Don't Care
Figure 24.1. T0 Mode 0 Block Diagram
TR0
0
1
GATE0
X
0
1
1
CKCON
M
T
1
0
1
M
T
0
S
C
A
1
Rev. 1.2
S
C
A
0
G
A
T
E
1
C
T
1
/INT0
/
M
T
1
1
TMOD
X
X
0
1
M
T
1
0
TCLK
G
A
T
E
0
C
T
0
/
M
T
0
1
M
T
0
0
(5 bits)
TL0
154), facilitating pulse width measure-
Counter/Timer
Disabled
Disabled
Enabled
Enabled
(8 bits)
for information on selecting and
TH0
TF1
TR1
TF0
TR0
IE1
IT1
IE0
IT0
Interrupt
Section