C8051F066-GQ Silicon Laboratories Inc, C8051F066-GQ Datasheet - Page 298

• Manufacturer Part Number: C8051F066-GQ
• Description: MCU 8-Bit C8051F06x 8051 CISC 32KB Flash 3.3V 100-Pin TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F06xr

Specifications of C8051F066-GQ

• Package: 100TQFP
• Device Core: 8051
• Family Name: C8051F06x
• Maximum Speed: 25 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 59
• Interface Type: I2C/SMBus/SPI/UART
• On-chip Adc: 2-chx16-bit
• Number Of Timers: 5
• Ram Size: 4.25 KB
• Program Memory Size: 32 KB
• Program Memory Type: Flash
• Operating Temperature: -40 to 85 °C
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 59
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 2x16b
• Oscillator Type: Internal
• Package / Case: 100-TQFP, 100-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 336-1221

C8051F060/1/2/3/4/5/6/7
24.2.4. Toggle Output Mode
Timer 2, 3, and 4 have the capability to toggle the state of their respective output port pins (T2, T3, or T4)
to produce a 50% duty cycle waveform output. The port pin state will change upon the overflow or under-
flow of the respective timer (depending on whether the timer is counting up or down). The toggle frequency
is determined by the clock source of the timer and the values loaded into RCAPnH and RCAPnL. When
counting DOWN, the auto-reload value for the timer is 0xFFFF, and underflow will occur when the value in
the timer matches the value stored in RCAPnH:RCAPnL. When counting UP, the auto-reload value for the
timer is RCAPnH:RCAPnL, and overflow will occur when the value in the timer transitions from 0xFFFF to
the reload value.
To output a square wave, the timer is placed in reload mode (the Capture/Reload Select Bit in TMRnCN
and the Timer/Counter Select Bit in TMRnCN are cleared to ‘0’). The timer output is enabled by setting the
Timer Output Enable Bit in TMRnCF to ‘1’. The timer should be configured via the timer clock source and
reload/underflow values such that the timer overflow/underflows at 1/2 the desired output frequency. The
port pin assigned by the crossbar as the timer’s output pin should be configured as a digital output (see
Section “18. Port Input/Output” on page
the pin. A Read/Write of the Timer’s Toggle Output State Bit (TMRnCF.2) is used to read the state of the
toggle output, or to force a value of the output. This is useful when it is desired to start the toggle of a pin in
a known state, or to force the pin into a desired state when the toggle mode is halted.
298
Equation 24.1. Toggle Mode Square Wave Frequency
F
sq
203). Setting the timer’s Run Bit (TRn) to ‘1’ will start the toggle of
=
---------------------------------------------------- -
2

Rev. 1.2

65536 RCAPn
F
TCLK
–
