C8051F066-GQ Silicon Laboratories Inc, C8051F066-GQ Datasheet - Page 291

• Manufacturer Part Number: C8051F066-GQ
• Description: MCU 8-Bit C8051F06x 8051 CISC 32KB Flash 3.3V 100-Pin TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F06xr

Specifications of C8051F066-GQ

• Package: 100TQFP
• Device Core: 8051
• Family Name: C8051F06x
• Maximum Speed: 25 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 59
• Interface Type: I2C/SMBus/SPI/UART
• On-chip Adc: 2-chx16-bit
• Number Of Timers: 5
• Ram Size: 4.25 KB
• Program Memory Size: 32 KB
• Program Memory Type: Flash
• Operating Temperature: -40 to 85 °C
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 59
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 2x16b
• Oscillator Type: Internal
• Package / Case: 100-TQFP, 100-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 336-1221

Bit7:
Bit6:
Bit5:
Bit4:
Bit3:
Bit2:
Bit1:
Bit0:
R/W
TF1
Bit7
TF1: Timer 1 Overflow Flag.
Set by hardware when Timer 1 overflows. This flag can be cleared by software but is auto-
matically cleared when the CPU vectors to the Timer 1 interrupt service routine.
0: No Timer 1 overflow detected.
1: Timer 1 has overflowed.
TR1: Timer 1 Run Control.
0: Timer 1 disabled.
1: Timer 1 enabled.
TF0: Timer 0 Overflow Flag.
Set by hardware when Timer 0 overflows. This flag can be cleared by software but is auto-
matically cleared when the CPU vectors to the Timer 0 interrupt service routine.
0: No Timer 0 overflow detected.
1: Timer 0 has overflowed.
TR0: Timer 0 Run Control.
0: Timer 0 disabled.
1: Timer 0 enabled.
IE1: External Interrupt 1.
This flag is set by hardware when an edge/level of type defined by IT1 is detected. It can be
cleared by software but is automatically cleared when the CPU vectors to the External Inter-
rupt 1 service routine if IT1 = 1. This flag is the inverse of the /INT1 signal.
IT1: Interrupt 1 Type Select.
This bit selects whether the configured /INT1 interrupt will be falling-edge sensitive or
active-low.
0: /INT1 is level triggered, active-low.
1: /INT1 is edge triggered, falling-edge.
IE0: External Interrupt 0.
This flag is set by hardware when an edge/level of type defined by IT0 is detected. It can be
cleared by software but is automatically cleared when the CPU vectors to the External Inter-
rupt 0 service routine if IT0 = 1. This flag is the inverse of the /INT0 signal.
IT0: Interrupt 0 Type Select.
This bit selects whether the configured /INT0 interrupt will be falling-edge sensitive or
active-low.
0: /INT0 is level triggered, active logic-low.
1: /INT0 is edge triggered, falling-edge.
TR1
R/W
Bit6
TF0
R/W
Bit5
Figure 24.4. TCON: Timer Control Register
TR0
R/W
Bit4
Rev. 1.2
R/W
IE1
Bit3
C8051F060/1/2/3/4/5/6/7
R/W
IT1
Bit2
R/W
IE0
Bit1
SFR Address:
SFR Page:
R/W
Bit0
IT0
0x88
0
Addressable
Reset Value
00000000
Bit
291