FDC37B727-NS Standard Microsystems (SMSC), FDC37B727-NS Datasheet - Page 143

• Manufacturer Part Number: FDC37B727-NS
• Manufacturer: Standard Microsystems (SMSC)

Specifications of FDC37B727-NS

• Pin Count: 128
• Lead Free Status / RoHS Status: Compliant

PME SUPPORT
The FDC37B72x offers support for PCI power
management
management event is requested by a PCI function
via the assertion of the nPME signal. The
assertion
asynchronous to the PCI clock.
FDC37B72x, active transitions on the ring indicator
inputs nRI1 and nRI2 or the nRING pin, active
keyboard-data edges, active mouse-data edges
and GPIOs GP10-GP17 can directly assert the
nPME signal. In addition, if the DEVINT_EN bit in
the PME_EN 1 Register is set, and if the
EN_SMI_PME bit in the SMI_EN 2 register is set,
then any of the SMI Events can also generate a
nPME.
diagrams below.
nPME functionality is controlled by the runtime
registers
<PM1_BLK>+11h.
PME_EN,
events. When PME_EN is inactive, the nPME
signal can not be asserted. When PME_EN is
asserted, any wake source whose individual
PME Wake Enable register bit is asserted can
cause nPME to become asserted. The PME
Wake Status register indicates which wake
source has asserted the nPME signal. The PME
Status bit, PME_STS, is asserted by active
transitions of PME Wake sources. PME_STS will
become asserted independent of the state of the
global PME enable, PME_EN.
In the FDC37B72x the nPME pin is an open
drain, active low, driver. The FDC37B72x nPME
pin is fully isolated from other external devices
that might pull the PCI nPME signal low; i.e., the
PCI nPME signal is capable of being driven high
externally by another active device or pullup
even when the the FDC37B72x VDD is
grounded, providing VTR power is active. The
FDC37B72x nPME driver sinks 6mA at .55V max
(see section 4.2.1.1 DC Specifications, page
122, in the PCI Local Bus Specification, Revision
2.1).
ACPI, PME AND SMI REGISTERS
See the SCI/PME and SMI/PME logic
and
globally
at
events
deassertion
<PM1_BLK>+Ch
controls
The
(PMEs).
PME
PME
of
Enable
nPME
A
Wake-up
through
In the
power
bit,
is
143
Logical Device A in the configuration section
contains the address pointer to the ACPI power
management register block, and PM1_BLK.
These are run-time registers;
PM1_BLK is an enable bit to allow the SCI group
interrupt to be routed to any interrupt or onto the
nPME/SCI pin.
register for SCI/PME/SMI selection function and
pin configuration bits.
Register Description
The ACPI register model consists of a number of
fixed register blocks that perform designated
functions. A register block consists of a number
of registers that perform Status, Enable and
Control functions. The ACPI specification deals
with events (which have an associated interrupt
status and enable bits, and sometimes an
associated control function) and control features.
The status registers illustrate what defined
function is requesting ACPI interrupt services
(SCI). Any status bit in the ACPI specification
has the following attributes:
A.
B.
C.
D.
Note that this implies that if the respective enable
bit is reset and the hardware event occurs, the
respective status bit is set, however no interrupt
is generated until the enable bit is set. This
allows software to test the state of the event (by
examining the status bit) without necessarily
generating an interrupt. There are a special class
of status bits that have no respective enable bit,
these are called out specifically, and the
Status bits are only set through some
defined “hardware event.”
Unless otherwise noted, Status bits are
cleared by writing a “HIGH” to that bit
position, and upon VTR POR. Writing a
0 has no effect.
Status bits only generate interrupts
while their associated bit in the enable
register is set.
Function bit positions in the status
register have the same bit position in
the
exceptions to this rule, special status
bits have no enables).
enable
Note: See IRQ mux control
register
Included in the
(there
are