ATMEGA16A-PU Atmel, ATMEGA16A-PU Datasheet - Page 29

MCU AVR 16K FLASH 16MHZ 40-PDIP

ATMEGA16A-PU

Manufacturer Part Number
ATMEGA16A-PU
Description
MCU AVR 16K FLASH 16MHZ 40-PDIP
Manufacturer
Atmel
Series
AVR® ATmegar
Datasheets

Specifications of ATMEGA16A-PU

Core Processor
AVR
Core Size
8-Bit
Speed
16MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
32
Program Memory Size
16KB (8K x 16)
Program Memory Type
FLASH
Eeprom Size
512 x 8
Ram Size
1K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
40-DIP (0.600", 15.24mm)
Processor Series
ATMEGA16x
Core
AVR8
Data Bus Width
8 bit
Data Ram Size
1 KB
Interface Type
2-Wire/SPI/USART
Maximum Clock Frequency
16 MHz
Number Of Programmable I/os
32
Number Of Timers
3
Maximum Operating Temperature
+ 85 C
Mounting Style
Through Hole
3rd Party Development Tools
EWAVR, EWAVR-BL
Development Tools By Supplier
ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
Minimum Operating Temperature
- 40 C
On-chip Adc
8-ch x 10-bit
Package
40PDIP
Device Core
AVR
Family Name
ATmega
Maximum Speed
16 MHz
Operating Supply Voltage
3.3|5 V
Controller Family/series
AVR MEGA
No. Of I/o's
32
Eeprom Memory Size
512Byte
Ram Memory Size
1KB
Cpu Speed
16MHz
Rohs Compliant
Yes
For Use With
ATSTK600 - DEV KIT FOR AVR/AVR32ATSTK500 - PROGRAMMER AVR STARTER KIT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATMEGA16A-PU
Manufacturer:
AT
Quantity:
20 000
Company:
Part Number:
ATMEGA16A-PU
Quantity:
25 000
8.7
8154B–AVR–07/09
Calibrated Internal RC Oscillator
Table 8-7.
Note:
The Calibrated Internal RC Oscillator provides a fixed 1.0, 2.0, 4.0, or 8.0 MHz clock. All fre-
quencies are nominal values at 5V and 25°C. This clock may be selected as the sys-tem clock
by programming the CKSEL Fuses as shown in
external components. The CKOPT Fuse should always be unpro-grammed when using this
clock option. During Reset, hardware loads the calibration byte into the OSCCAL Register and
thereby automatically calibrates the RC Oscillator. At 5V, 25°C and 1.0, 2.0, 4.0 or 8.0 MHz
Oscillator frequency selected, this calibration gives a frequency within ± 3% of the nominal fre-
quency. Using calibration methods as described in application notes available at
www.atmel.com/avr it is possible to achieve ±1% accuracy at any given V
When this Oscillator is used as the Chip Clock, the Watchdog Oscillator will still be used for the
Watchdog Timer and for the reset time-out. For more information on the pre-programmed cali-
bration value, see the section
Table 8-8.
Note:
When this Oscillator is selected, start-up times are determined by the SUT Fuses as shown in
Table
Table 8-9.
Note:
SUT1:0
SUT1:0
10
00
01
10
11
00
01
11
8-9. XTAL1 and XTAL2 should be left unconnected (NC).
(1)
1. This option should not be used when operating close to the maximum frequency of the device.
1. The device is shipped with this option selected.
1. The device is shipped with this option selected.
CKSEL3:0
Start-up Times for the External RC Oscillator Clock Selection
Start-up Time from
Internal Calibrated RC Oscillator Operating Modes
Start-up Times for the Internal Calibrated RC Oscillator Clock Selection
0001
Power-down and
0010
0011
0100
Start-up Time from
Power-save
Power-down and
(1)
6 CK
18 CK
18 CK
18 CK
Power-save
6 CK
6 CK
6 CK
(1)
“Calibration Byte” on page
Additional Delay
(V
from Reset
CC
4.1 ms
4.1 ms
65 ms
Additional Delay
= 5.0V)
(V
from Reset
CC
4.1 ms
65 ms
Table
Reserved
= 5.0V)
Nominal Frequency (MHz)
8-8. If selected, it will operate with no
266.
BOD enabled
Fast rising power
Slowly rising power
Recommended Usage
Fast rising power or BOD enabled
1.0
2.0
4.0
8.0
Recommended Usage
BOD enabled
Fast rising power
Slowly rising power
ATmega16A
CC
and Temperature.
29

Related parts for ATMEGA16A-PU