MCHC908GR8CFAE Freescale Semiconductor, MCHC908GR8CFAE Datasheet - Page 194

• Manufacturer Part Number: MCHC908GR8CFAE
• Description: IC MCU FLSH 8BIT8MHZ 7.5K32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MCHC908GR8CFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 21
• Program Memory Size: 7.5KB (7.5K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 384Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08G
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8.2 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 6 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Monitor ROM (MON)
Technical Data
194
NOTE:
requirements and conditions, are not in effect. This is to reduce circuit
requirements when performing in-circuit programming.
If the reset vector is blank and monitor mode is entered, the chip will see
an additional reset cycle after the initial POR reset. Once the part has
been programmed, the traditional method of applying a voltage, V
IRQ must be used to enter monitor mode.
The COP module is disabled in monitor mode based on these
conditions:
The second condition states that as long as V
IRQ pin after entering monitor mode, or if V
the initial reset to get into monitor mode (when V
then the COP will be disabled. In the latter situation, after V
to the RST pin, V
freeing the IRQ for normal functionality in monitor mode.
Figure 15-2
the reset vector is blank and just 1 x V
pin. An external oscillator of 9.8304 MHz is required for a baud rate of
9600, as the internal bus frequency is automatically set to the external
frequency divided by four.
Freescale Semiconductor, Inc.
•
•
For More Information On This Product,
If monitor mode was entered as a result of the reset vector being
blank (condition set 2 or 3), the COP is always disabled regardless
of the state of IRQ or RST.
If monitor mode was entered with V
then the COP is disabled as long as V
or RST.
shows a simplified diagram of the monitor mode entry when
Go to: www.freescale.com
Monitor ROM (MON)
TST
can be removed from the IRQ pin in the interest of
DD
TST
voltage is applied to the IRQ
TST
TST
on IRQ (condition set 1),
TST
TST
MC68HC908GR8 — Rev 4.0
is applied to RST after
is applied to either IRQ
is maintained on the
was applied to IRQ),
TST
MOTOROLA
is applied
TST
, to