MCHC908GR8CFAE Freescale Semiconductor, MCHC908GR8CFAE Datasheet - Page 264

• Manufacturer Part Number: MCHC908GR8CFAE
• Description: IC MCU FLSH 8BIT8MHZ 7.5K32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MCHC908GR8CFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 21
• Program Memory Size: 7.5KB (7.5K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 384Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08G
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8.2 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 6 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Serial Communications Interface (SCI)
18.9.5 SCI Status Register 2
Technical Data
264
Address:
SCI status register 2 contains flags to signal the following conditions:
BKF — Break Flag Bit
RPF — Reception in Progress Flag Bit
Reset:
Read:
Write:
Freescale Semiconductor, Inc.
•
•
This clearable, read-only bit is set when the SCI detects a break
character on the PE1/RxD pin. In SCS1, the FE and SCRF bits are
also set. In 9-bit character transmissions, the R8 bit in SCC3 is
cleared. BKF does not generate a CPU interrupt request. Clear BKF
by reading SCS2 with BKF set and then reading the SCDR. Once
cleared, BKF can become set again only after logic 1s again appear
on the PE1/RxD pin followed by another break character. Reset
clears the BKF bit.
This read-only bit is set when the receiver detects a logic 0 during the
RT1 time period of the start bit search. RPF does not generate an
interrupt request. RPF is reset after the receiver detects false start bits
(usually from noise or a baud rate mismatch) or when the receiver
detects an idle character. Polling RPF before disabling the SCI
module or entering stop mode can show whether a reception is in
progress.
For More Information On This Product,
1 = Break character detected
0 = No break character detected
1 = Reception in progress
0 = No reception in progress
Break character detected
Incoming data
Serial Communications Interface (SCI)
$0017
Bit 7
0
Figure 18-14. SCI Status Register 2 (SCS2)
Go to: www.freescale.com
= Unimplemented
6
0
5
0
4
0
3
0
MC68HC908GR8 — Rev 4.0
2
0
BKF
1
0
MOTOROLA
Bit 0
RPF
0