AT91SAM7X128-CU Atmel, AT91SAM7X128-CU Datasheet - Page 109

• Manufacturer Part Number: AT91SAM7X128-CU
• Description: MCU ARM 128K HS FLASH 100-TFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7X128-CU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: CAN, Ethernet, I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFBGA
• For Use With: AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9AT91SAM7X-EK - KIT EVAL FOR AT91SAM7X256/128
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Figure 19-6. Example of Partial Page Programming:
19.2.4.2
6120H–ATARM–17-Feb-09
16 words
16 words
16 words
16 words
Erase All Command
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
Erase All Flash
Page 7 erased
32 bits wide
Step 1.
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
...
...
...
...
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
After programming, the page (the whole lock region) can be locked to prevent miscellaneous
write or erase sequences. The lock bit can be automatically set after page programming using
WPL.
Data to be written are stored in an internal latch buffer. The size of the latch buffer corresponds
to the page size. The latch buffer wraps around within the internal memory area address space
and appears to be repeated by the number of pages in it.
Note:
Data are written to the latch buffer before the programming command is written to the Flash
Command Register MC_FCR. The sequence is as follows:
Two errors can be detected in the MC_FSR register after a programming sequence:
The entire memory can be erased if the Erase All Command (EA) in the Flash Command Regis-
ter MC_FCR is written.
• Write the full page, at any page address, within the internal memory area address space
• Programming starts as soon as the page number and the programming command are written
• When programming is completed, the bit FRDY in the Flash Programming Status Register
• Programming Error: A bad keyword and/or an invalid command have been written in the
• Lock Error: The page to be programmed belongs to a locked region. A command must be
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
using only 32-bit access.
to the Flash Command Register. The FRDY bit in the Flash Programming Status Register
(MC_FSR) is automatically cleared.
(MC_FSR) rises. If an interrupt was enabled by setting the bit FRDY in MC_FMR, the
interrupt line of the Memory Controller is activated.
MC_FCR register.
previously run to unlock the corresponding region.
Writing of 8-bit and 16-bit data is not allowed and may lead to unpredictable data corruption.
Programming of the second part of Page 7
AT91SAM7X512/256/128 Preliminary
FF
FF
FF
CA FE
CA FE
CA FE
FF
FF
FF
FF
FF
FF
(NEBP = 1)
32 bits wide
FF
FF
FF
FF
FF
FF
FF
FF
FF
Step 2.
...
...
...
...
CA
CA
CA
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FE
FE
FE
Programming of the third part of Page 7
CA FE
CA FE
CA FE
FF
FF
FF
DE CA
DE CA
DE CA
FF
FF
FF
(NEBP = 1)
32 bits wide
FF
FF
FF
FF
FF
FF
Step 3.
...
...
...
...
CA
CA
CA
FF
FF
FF
DE CA
DE CA
DE CA
FF
FF
FF
FF
FF
FF
FE
FE
FE
FF
FF
FF
109